Johnson & Starley Quantec HR28C ErP Скачать руководство пользователя страница 37

Страница: 37 / 44

Sales/Spares & Replacement Help Line 01604 762881

FLUE TEMPERATURE SENOR LOCKOUT

NO DISPLAY

NO DHW BUT CH ON

YES

Is the wiring secure to 9 way connector X5 on Interface PCB

Replace the PCB

Connect the wiring.

Supply power to boiler.

Connect the wiring from the terminal block to the

Main PCB securely.

Secure connection.

Is the wiring securely connected to sensor?

Is there 230VAC to the boiler at L & N?

See graph Figure 51.

Is the wiring from the terminal block to the main PCB connected securely?

NO CH OPERATION BUT DHW WORKS OK

YES

Are the radiator valves open?

Replace the diverter valve

Toggle to the Winter position.

Switch the timer and room

thermostat on.

There is no voltage from the

timer/room thermostat. This

is not a boiler fault. Ensure

voltage is supplied to the

boiler by rectifying external

wiring.

Open the radiator valves.

Is the mode knob in the Winter position?

Are the timer and room thermostat switched on?

Is there 24V at ‘A’? (see diagram)

YES

Is the hot & cold pipework crossed?

Replace the PCB.

Is the wiring connected between PCB &

DHW sensor?

Re-connect wiring

Replace turbine

sensor.

Remove the turbine,

check for debris in

the turbine & filter.

Replace turbine if

necessary. IS DHW

working?

YES

Is the turbine working?

Adjust flow rates to achieve 35° temperature

rise and check filter fitted in turbine is not

blocked with debris.

Reconnect the wiring or replace wiring

harness if no continuity.

Re-engage diverter head and secure clip to

group set.

Change diverter Valve cartridge - rear

section.

Change diverter Valve cartridge - rear

section.

Replace the PCB.

Does the display show the hot water symbol?

Are the flow rates correct?

Is the wiring between the PCB and the

diverter valve motor connected?

Check diverter head is fully engaged and clip

is secured onto group set?

Check and replace diverter valve motor head.

Is boiler DHW working?

Check and replace diverter valve motor head.

Is boiler DHW working?

Is diverter stuck in the CH position

Содержание Quantec HR28C ErP













































Результаты поиска

Содержание Quantec HR28C ErP

Отзывы:

Похожие инструкции для Quantec HR28C ErP

Бренды по названию

Популярные бренды

Johnson & Starley Quantec HR28C ErP, Инструкции по установке, пусконаладке и обслуживанию

Результаты поиска

Содержание Quantec HR28C ErP

Отзывы:

Похожие инструкции для Quantec HR28C ErP

Бренды по названию

Популярные бренды