Johnson & Starley Quantec HR28C ErP Скачать руководство пользователя страница 29

Страница: 29 / 44

Sales/Spares & Replacement Help Line 01604 762881

FIGURE 35. QUANTEC HR28C

INTERNAL COMPONENTS

17.8 HEAT

EXCHANGER

Refer to paragraphs 17.5 to 17.7
17.8.1 Inspect the inside of the combustion chamber, with a soft brush remove any deposits that may have

occurred. Flush with clean water. DO NOT use any chemicals.

17.8.2

Inspect the heat exchangers insulation at the front and back of the combustion chamber for any signs of
damage.

17.8.3 If there are any signs of damage on the flue outlet then this must be

replaced.

17.8.4

Check the gaskets of burner door and burner, If they show signs of damage
then replace.

17.8.5

Refit in reverse order.

17.9 CONDENSATE

TRAP

Refer to paragraph 17.5.
17.9.1

Unscrew the 2 pipes and pull off the third pipe.

17.9.2

Remove the trap and clean by removing the cleaning plug. Flush out any
deposits with clean water.

17.9.3

Refit the trap and the pipes.

17.9.4

Refit in reverse order.

FIGURE 34. CONDENSATE TRAP

RETURN

TEMPERATURE

SENSOR

DHW FLOW

TURBINE

AUTOMATIC

AIR VENT

PRESSURE

RELIEF VALVE

(at the rear)

PUMP

GAS VALVE

DHW FILTER &

FLOW REGULATOR

(in front of plate heat exchanger)

PLATE HEAT

EXCHANGER

(at the rear)

FLOW

THERMISTOR

SENSOR

EXPANSION

VESSEL

RAIN TRAP

IGNITION & FLAME

DETECTION

ELECTRODE

BURNER

INJECTOR

VENTURI

VIEW PORT

BURNER

ARM

HEAT

EXCHANGER

DRAIN PIPE

FLUE GAS

TEMPERATURE

SENSOR

FLUE TEST

POINT

FLUE

ADAPTER

CONDENSATE

TRAP

FAN

DHW

TEMPERATURE

SENSOR

WATER

PRESSURE

SENSOR

THREE WAY

DIVERTER

HEAD

DIVERTOR

VALVE

Содержание Quantec HR28C ErP













































Результаты поиска

Содержание Quantec HR28C ErP

Отзывы:

Похожие инструкции для Quantec HR28C ErP

Бренды по названию

Популярные бренды

Johnson & Starley Quantec HR28C ErP, Инструкции по установке, пусконаладке и обслуживанию

Результаты поиска

Содержание Quantec HR28C ErP

Отзывы:

Похожие инструкции для Quantec HR28C ErP

Бренды по названию

Популярные бренды