background image

www.johnsonandstarley.co.uk

3.  IMPORTANT INFORMATION

 

Installation shall be in accordance with the current editions of:-

 

Building Standards (Scotland) (Consolidation) Regulations

 

Building Regulations

 

Gas Safety (Installation and Use) Regulations (as amended)

 

BS 7671 Institute of Electrical Engineers (I.E.E.) Wiring Regulations

 

BS 6891 Installation of Low Pressure Gas Pipework of up to 28mm (R1) in domestic premises (2nd family gases).

 

BS 5440 Pt.1 (Flues for Gas Appliances)

 

BS 5440 Pt.2 (Air Supply for Gas Appliances)

 

BS 5864 Installation of Gas Fired Ducted Air Heaters

 

British System Design Manual “Gas Fired Warm Air Heating”

 

Model and Local Authority Bye-laws

 

BS 5546 Installation of Domestic Hot Water Supplies.

IT IS A

 

STATUTORY REQUIREMENT THAT ALL GAS APPLIANCES MUST BE INSTALLED BY COMPETENT PERSONS, 

(i.e. GAS SAFE REGISTERED INSTALLERS. GAS SAFE MEMBERSHIP ENQUIRIES - TEL: 0800 408 5500) IN 
ACCORDANCE WITH THE GAS SAFETY (INSTALLATION AND USE) REGULATIONS (CURRENT EDITION). FAILURE 
TO COMPLY WITH THESE REGULATIONS MAY LEAD TO PROSECUTION.

4.  TECHNICAL DATA

ECONOMAIRE 32

ECONOMAIRE 32 INTEJAN

WATER CIRCULATOR

WEIGHT

54kg

61kg

GAS

G20

GAS SUPPLY PRESSURE

20mbar

GA CATEGORY

I  2H

COUNTRIES OF INSTALLATION

GB & IE

ELECTRICAL SUPPLY

230V  ~  50Hz  fused  5A 250W

NOX CLASS

1

MAXIMUM WATER SIDE OPERATING PRESSURE 
(PMS)

N/A

3 bar

OPEN VENTED SYSTEM

N/A

YES

SEALED SYSTEM

N/A

YES

5.  HEATER COMPARTMENT AND CLEARANCES 

(See BS 5864)

5.1  

IMPORTANT:

 

If the heater is to be fitted to an existing base duct (warm air plenum), always ensure that installation 

is carried out such that the rear left hand corner of the heater is aligned with the rear left hand corner of the base duct, 
so that any overhang or blanking off will be at the front and/or right hand side. In any event, blanking plates must be 
mechanically secured and all joints sealed.

5.2   When the heater is fitted into a compartment, a minimum clearance from the compartment walls of 3mm (

1

/

8

”) at the 

sides and rear and 75mm (3”) at the front must be left. Consideration should also be given to the space required for 
the removal and replacement of the filter tray and the entry of the gas, water and electrical supplies. If gas and /or water 
connections are made from a side entry, a minimum clearance of 75mm (3”) is required at that side.

5.3   For service access, a minimum of 450mm (18”) is required at the front of the heater. Space must also be allowed, in a 

compartment installation, to permit the removal of the heater. The clearance between the appliance and the compartment 
should be not less than 75mm (3”). However, if clearances are less than 75mm, the  internal surface of the compartment 
must be lined with non-combustible material and the compartment must be of a fixed rigid structure.

5.4   In airing cupboard installations, the part used as the air heater compartment must comply with the relevant section of 

BS 5864 and must be completely separated by either a non-combustible partition or a perforated metal partition with the 
perforations not exceeding 13mm (½”). The secondary flue must be a tight fit where it passes through the partition and 
must be suitably protected (see BS 5440: Part 1).

Содержание ECONOMAIRE 32

































Отзывы: