www.joerns.com | [email protected]
Joerns Support Surface
Arise
®
LAL Mattress Replacement,
Arise LAL Overlay, Arise 1000, Arise 1000EX
Sequentially reduce the
Comfort Adjust
setting
to the firmness level where the height of the
three (3) or four (4) fingers can slide with
minimal resistance between the patient’s
sacral area/buttocks and the lower safety
mattress. This is the proper
Comfort Adjust
setting for the patient to assure proper inflation
of the air cells and prevent bottoming out of
the mattress.
Document the patient’s
Comfort Adjust
setting for future reference, and re-evaluate
with the Hand Check as the patient’s
condition warrants.
Arise
®
LAL Mattress Setup
Remove the existing mattress from the bed.
Place the Arise LAL mattress with the hose
connection at the foot end of the bed and the
therapy cells facing up. Secure the six (6) straps
on the mattress securely to the movable part of the
bed frame.
If the therapy pad is not already on the mattress,
attach it securely to the mattress.
Hang the control unit on the foot of the bed facing
away from the bed. Attach the hose connector
marked CPR to the underside of the control unit.
Plug the Fowler Boost sensor into the side of the
control unit.
Plug in the control unit and the yellow
Standby
light will illuminate. Press the
Power
key.
The control unit will start and the green light
will illuminate.
Allow three to five minutes for full inflation
Select the appropriate
Comfort Adjust
setting
(Refer to “Comfort Adjust Setup” section).
The CairRails risk management side air bolsters
can be inflated or deflated as required. Locate
the turn valve on the hose assembly between the
mattress and the control unit. Next, inflate/deflate
the CairRails by moving the turn valve to the up
(inflate) or down (deflate) position.
Note:
When inflating or deflating CairRails it is
recommended that the support surface be in
Autofirm
mode.
Arise
®
LAL Overlay Setup
Place the Arise LAL overlay on top of the mattress
with the hose connection at the foot end of the bed
and the therapy cells facing up. Secure the straps
around the head and foot ends of the mattress.
Fasten the two straps by the seat section securely
to the sleep deck of the bed frame.
4.
5.
•
•
•
•
•
•
•
•
•
•
If the therapy pad is not already on the overlay,
attach it securely using the zippers.
Hang the control unit on the foot of the bed
facing away from the bed. Attach the hose
connector marked
CPR
to the underside of the
control unit.
Plug the Fowler Boost sensor into the side of the
control unit.
Plug in the control unit and the yellow
Standby
light will illuminate. Press the
Power
key.
The control unit will start and the green light
will illuminate.
Allow three to five minutes for full inflation.
Place the patient on the overlay. Overlay can
be inflated with patient on it, but will take longer,
depending on patient weight/size.
Note:
Keep the control unit on while the patient
is on the overlay.
The CairRails air side bolsters are currently not
available with the Arise LAL overlay.
Arise 1000 Mattress Setup
Remove the existing mattress from the bed.
Place the Arise 1000 mattress with the hose
connection at the foot end of the bed and the
therapy cells facing up. Secure the ten (10)
straps on the mattress securely to the movable
part of the bed frame.
If the therapy pad is not already on the mattress,
attach it securely to the mattress.
Hang the control unit on the foot of the bed
facing away from the bed. Attach the hose
connector marked
CPR
to the underside of the
control unit.
Plug the Fowler boost sensor into the side of the
control unit.
Plug in the control unit and the yellow
Standby
light will illuminate. Press the
Power
key.
The control unit will start and the green light
will illuminate.
Allow three to five minutes for full inflation
Select the appropriate
Comfort Adjust
setting
(Refer to “Comfort Adjust Setup” section).
The CairRails risk management side air bolsters
can be inflated or deflated as required. Locate
the turn valve on the hose assembly between
the mattress and the control unit. Next, inflate/
deflate the CairRails by moving the turn valve to
the up (inflate) or down (deflate) position.
Note:
When inflating or deflating CairRails it is
recommended that the support surface be in
Autofirm
mode.
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
9
Electronic Copy: Reference Only
