Joab EcoDrive Скачать руководство пользователя страница 28 | Manualshive

Страница: 28 / 73

background image

The continuous-hydraulic-supply is not the same as tipping or lowering a trailer. When the trailer
is simply lowered or tipped, a hydraulic feed is provided only during the time the function is activ-
ated. In contrast, the continuous-hydraulic-supply is constantly fed to the tip-trailer and can be
either increased or decreased as required. Note, not all vehicles are equipped with the ability to
increase or decrease the flow of hydraulic fluid.

The hydraulic supply to a tip trailer is normally fed from the hook-lift's connector on the back of
the vehicle.

The CBW controller is used to control the flow of hydraulic fluid to the tip-trailer. The flow is ini-
tially set at 0L/min and must be set to the required value by the driver using the tip trailer icons.
Refer to

Once a value for the hydraulic supply has been set, using the tip-trailer icons, it is saved. If the
unit or power supply is turned off, the value is still saved. It can be changed again, if desired, at
any time.

After setting the continuous-hydraulic-supply, it can be started by simply selecting its icon, as
shown below. The hydraulic supply will flow at the saved rate of flow.

There is no hydraulic flow sensor in the supply line to the tip trailer. Therefore, an external flow
sensor will be required if the hydraulic flow is to be measured.

To operate the hydraulic supply to the tip trailer use the functions listed below.

Icon

Function

Start the continuous-hydraulic-supply. The power-take-of must be active.

Increase the continuous-hydraulic-supply

Decrease the continuous-hydraulic-supply

Stop the continuous-hydraulic-supply

Table 6: Hydraulic supply to tip trailer

Emergency Stop

In case of an emergency, such as a hydraulic leak or risk of injury, an emergency stop button is fit-
ted to the CBW controller (see

"CBW controller", on page 11

). Pressing the emergency stop but-

20

Operation | CBW controller

EcoDrive manual: 13300 Edition 1 | 2019-01-31

«
...
26
27
28
29
30
...
»

Содержание EcoDrive










































































Отзывы:

Нет отзывов

Похожие инструкции для EcoDrive

Бренд: ESAB Страницы: 21

VIPER MULTI 135

Бренд: Unimig Страницы: 48

Бренд: Keurig Страницы: 6

Бренд: ATH Страницы: 76

Бренд: Miller Страницы: 56

Бренд: omisa Страницы: 44

POWER CUT 60HFIII

Бренд: Mweld Страницы: 24

Бренд: R-Tech Страницы: 23

Бренд: Lincoln Electric Страницы: 16

Бренд: Migomag Страницы: 13

Бренд: Lutron Electronics Страницы: 36

Бренд: Carel Страницы: 94

Бренд: Tews Technologies Страницы: 22

Enado Mini ENA-MINI-010

Бренд: Wyrestorm Страницы: 2

Бренд: PLASMATECH Страницы: 58

MAGSTOP MIB 10-C090

Бренд: Magnetic Autocontrol Страницы: 15

Бренд: ICP DAS USA Страницы: 6

Бренд: Kabola Страницы: 27

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды