Joab EcoDrive Скачать руководство пользователя страница 24 | Manualshive

Страница: 24 / 73

background image

Background Light

The background light for the user interface can be adjusted as required. This function allows the
user to quickly adjust the background light so that it is possible to read the display, when for
example there is a lot of sun shining on the display.

To adjust the background light simply press the OK button with a short press repeatedly to
switch between 100%, 20%, and 0% background light.

The display will automatically turn off whenever the hydraulic pump is off. It will only remain on if
there is a warning to display, as listed under

. below.

Warnings

The user interface will display warnings whenever the hydraulic pump is not in operation. These
warnings display an icon indicating the following states:

Icon

Meaning

The hook lift is not fully retracted.

The hydraulic-lock is open.

The center-lock is open.

Safety-hook is open (LA models).

Table 3: User interface warnings

Control Stick Function

Listed below in Table 4 are the functions that the control stick has. For information regarding the
control of snow ploughs refer to

"Snow Plough Functions", on page 18

Tip Up

Tip Up

Fast Operation*

Extending-Section

IN

Pull backwards

Bottom button pressed

and pull backwards

Turn the knob ant-clockwise

Table 4: CBW controller stick functions

16

Operation | CBW controller

EcoDrive manual: 13300 Edition 1 | 2019-01-31

«
...
22
23
24
25
26
...
»

Содержание EcoDrive










































































Отзывы:

Нет отзывов

Похожие инструкции для EcoDrive

Бренд: Zmotion Страницы: 48

7.4VOLT HEATED GLOVES

Бренд: Mobile Warming Страницы: 6

Бренд: KAR-TECH Страницы: 55

NeverFreeze SX-0810-24

Бренд: ThermoSoft Страницы: 5

Бренд: NCR Страницы: 12

Бренд: birddog Страницы: 30

Arc Welder 55 - 160A

Бренд: Silverline Страницы: 46

GALA TIG 3200 ACDC

Бренд: GALAGAR Страницы: 4

Hy-Brid 3 Series

Бренд: Custom Equipment Страницы: 23

Laron BL digital

Бренд: BAK Thermoplastic Welding Technology Страницы: 13

Бренд: WAGO Страницы: 82

Бренд: Bloomfield Страницы: 16

Бренд: ReadyLift Страницы: 20

Бренд: Omron Страницы: 398

Бренд: IDENTEC SOLUTIONS Страницы: 26

Бренд: WAGO Страницы: 50

Бренд: Worldwel Страницы: 5

Бренд: HERKULES Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды