Joab EcoDrive Скачать руководство пользователя страница 71

Страница: 71 / 73

Fault Tracing the Hook-Lift

Provided below is a simple troubleshooting guide that can help to identify the most common
faults with a hook-lift.

Fault

Cause

Action

Noise from pump.

1. The pump is sucking air.

2. Incorrect amount of oil.

3. The pump is defective

1. Check connections.

2. Adjust the amount of oil.

3. Replace the pump.

Nothing works

1. Emergency stop is activ-

ated

2. Fuse/relay blown

1. Switch off the engine, pull

out the emergency stop,
and restart.

2. Replace the fuse/relay

Noise from cylinders

Jerky hydraulic move-
ment.

Oil sprays from the
tank.

1. The piston rod is defect-

ive

2. Air in the hydraulic sys-

tem.

3. Valve or piston fault in

pump.

4. Tank oil level too high or

low.

5. Pump draws air.

6. The tank’s air filter is

blocked.

1. Replace the piston rod.

2. Check that the suction line is

sealed.

3. Service or replace the

pump.

4. Regulate the oil level.

5. Service or replace the

pump.

6. Replace the filter.

Poor lifting capacity

1. Insufficient amount of oil

to the pump

2. Oil pressure too low.

3. Leaking cylinder gas-

kets.

1. Check the oil level.

2. Contact JOAB.

3. Replace the cylinder gas-

kets.

Controller electric
levers jam.

1. Chain lock/lever jams.

2. Spring set for air cyl

broken.

3. Electric solenoid jams.

1. Remove, lubricate, and rein-

stall

2. Replace spring set

3. Clean the solenoid. If neces-

sary, replace it.

Table 12: Fault tracing the hook-lift

EcoDrive manual: 13300 Edition 1 | 2019-01-31

Содержание EcoDrive










































































Результаты поиска

Содержание EcoDrive

Отзывы:

Joab EcoDrive, Руководство по эксплуатации и обслуживанию, Страница: 71 / 73

Результаты поиска

Содержание EcoDrive

Отзывы: