JFD B44771 Скачать руководство пользователя

Страница: 89 / 136

OM131

P1939-OM-131 R11

Chapter 4

4.4 F

AULT

DIAGNOSIS

A schedule of possible faults and remedies for various conditions of reduced performance of the
Backpack is shown in

Table 4.1 to aid fault diagnosis.

Table 4.1 Fault finding

Fault

Probable Cause

Solution

External gas leak from
scrubber door.

Main O-ring cut or torn.

Replace main O-ring seal on
scrubber door.

Scrubber door damaged.

Replace scrubber door.
(See Section 4.5.1)

Internal gas leak from
scrubber canister.

Sealing gasket cut or torn.

Replace gasket.

Scrubber lift mechanism not
providing sufficient sealing.

Replace scrubber lift
mechanism.

External gas leak from upper
part of main housing.

Leak from one of the upper
penetrators.

Replace upper penetrator o-
rings.
(See Section 4.5.2)

External gas leak from lower
part of main housing.

Leak from one of the lower
penetrators.

Replace lower penetrator o-
rings.
(See Section 4.5.3)

External air leak from charging
point.

Check valve seat cut or
damaged.

Replace charging point check
valve seat.
(See Section 4.5.4)

External leak from burst disc.

Burst disc ruptured.

Replace burst disc.
(See Section 4.5.5)

Failure to pass flow test.

Restriction in injection orifice.

Ultrasonically clean injection
orifice and retest.

External gas leak from
demand regulator.

Sealing O-ring cut or torn.

Replace O-ring.
(See Section 4.5.6)

Damaged Diaphragm.

Replace Diaphragm.
(See Section 4.5.6)

Leaking Relief Valve

Replace Relief Valve.
(See Section 4.5.6)

Demand regulator body
damaged.

Replace regulator body.
(See Section 4.5.6)

Harness damaged.

Various.

Replace harness.
(See Section 4.5.7)

External air leak from
counterlung.

Counterlung cut or torn.

Replace counterlung.
(See Section 4.5.8)

Overpressure indicator not
operating.

Various.

Return to Divex Ltd for repair.

Содержание B44771









































































































































Результаты поиска

Содержание B44771

Отзывы:

Похожие инструкции для B44771

Бренды по названию

Популярные бренды

JFD B44771, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание B44771

Отзывы:

Похожие инструкции для B44771

Бренды по названию

Популярные бренды