JFD B44771 Скачать руководство пользователя | Manualshive

Страница: 70 / 136

background image

58

OM131

Chapter 4

P1939-OM-131 R11

4.3.1.3 Check actuation of SLS system backpack

1.

Remove the outer door, scrubber door and CO

2

scrubber canister.

2.

Actuate the SLS System by pulling the actuation handle.

N

OTE

The actuation effort should not exceed 10kg if the equipment is well maintained.

3.

Check that the spool valve has actuated and that there is a bleed of gas into the SLS System,
by listening for a flow.

4.3.1.4 Check gas flow from single stage regulator

N

OTE

This should be done with the supply hose connected to the Helmet to ensure that the single stage
regulator inlet filter and the helmet side-block connector filter are not contaminated and restricting
the flow.

1.

Connect the SLS System Backpack single stage regulator hose to the SLS System Helmet
sideblock and connect an AIR supply to the helmet.

2.

Remove the blanking plug from the first stage regulator test port and insert the test gauge
(Divex Part No. DM32540) from the Tool and Test Kit.

3.

Remove the scrubber door and CO

2

scrubber canister.

4.

Insert the flowmeter connector (Divex Part No. DM32580) from the Tool and Test Kit into the
main supply penetrator.

5.

Connect a breathing quality AIR supply directly to the umbilical hose on the SLS System and
set a supply pressure equal to the expected helmet supply pressure from the tables in chapter
3 of the SLS Helmet Manual OM112.

6.

Blank the top port on the test flowmeter (Divex Part No. DM32580).

7.

Allow the test hose to pressurise until the pressure stabilises.

8.

Check the pressure gauge, which should read 138 mbar (2 psi).

9.

If not adjust regulator by slackening locknut (Fig 4.8, Item 17, page 74) and using the Allen
key provided, move the regulator adjustment screw, until 138 mbar (2 psi) is reached and
tighten the locknut.

6

Counterlung Assembly

CA2607

7

Weight Pocket

D308

8

Handle Retaining Band

D302

9

Rescue Lifting Point

-

10

Cable Wiper Sleeve

D328

11

Bush

D322

Item

Description

Part No

«
...
68
69
70
71
72
...
»

Содержание B44771









































































































































Отзывы:

Нет отзывов

Похожие инструкции для B44771

Бренд: X-laser Страницы: 17

MTEK6000 Series

Бренд: Metretek Страницы: 81

Бренд: Danfoss Страницы: 80

Бренд: Prolude Amplification Страницы: 15

Signet FlowtraMag 2580 Series

Бренд: GF Страницы: 20

Бренд: Ocea Soft Страницы: 19

Бренд: Hilti Страницы: 146

Бренд: Bruker BioSpin Страницы: 76

Бренд: Kabelmat Страницы: 27

Бренд: Vanguard Instruments Company Страницы: 111

Бренд: CryptOn Страницы: 13

Бренд: BERG Страницы: 23

PMD Analyzer 5500B

Бренд: EXFO Страницы: 4

Бренд: Keysight Страницы: 42

Бренд: VITO Страницы: 36

Бренд: MetLogix Страницы: 30

Бренд: JET CITY AMPLIFICATION Страницы: 12

PA 900 Musikant

Бренд: Korg Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды