JFD B44771 Скачать руководство пользователя | Manualshive

Страница: 48 / 136

background image

36

OM131

Chapter 3

P1939-OM-131 R11

6.

Charge the SLS System to the required charging pressure (see Table 3.2 for details). Slowly
pressurise the gas cylinders. Ensure, using torch, that an excessive temperature rise does
not occur within the cylinders during this operation. If the cylinders become too warm to touch,
stop charging and leave the cylinders to cool before continuing.

The use of a Divex portable booster skid (Divex Part No. DM1480) is recommended to assist in
charging if the required cylinder charging pressure is greater than that available from storage.

N

OTES

(1) When charging the SLS System using enriched oxygen mixes (mixes containing greater than

21% oxygen), the gas booster should not be required. These gases should be decanted directly
into the SLS System. The required charging pressures are given on the Table 3.2.

(2) After carrying out shallow training dives with the SLS System, care must be taken to ensure that

the O

2

rich mixture used is fully vented from the SLS System before recharging with the correct

gas mix for the proposed working depth. After completion of training dives, the cylinders should
be vented, then charged then vented again and then recharged to ensure the gas mix for the
working depth has not been compromised.

7.

Vent the charging whip and disconnect.

8.

Replace the blanking cap on the charging point.

«
...
46
47
48
49
50
...
»

Содержание B44771









































































































































Отзывы:

Нет отзывов

Похожие инструкции для B44771

Бренд: ABB Страницы: 8

Бренд: Yamaha Страницы: 2

Бренд: DigiTech Страницы: 8

Бренд: UEi Страницы: 5

Бренд: Lasertec Страницы: 28

Бренд: RADWAG Страницы: 176

Бренд: M&C Страницы: 18

Бренд: CONDTROL Страницы: 27

Бренд: Tegam Страницы: 36

Бренд: Ofs Страницы: 28

DOC026.52.00769

Бренд: Hach Страницы: 64

Бренд: Fluke Страницы: 22

Бренд: DynAmp Страницы: 43

Бренд: Kimo Страницы: 80

Бренд: Cable Detection Страницы: 2

Бренд: Omega Страницы: 12

Бренд: PASCO Страницы: 18

Бренд: MGC Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды