JFD B44771 Скачать руководство пользователя | Manualshive

Страница: 84 / 136

background image

72

OM131

Chapter 4

P1939-OM-131 R11

4.3.4.3 Strip down and service of single stage regulator

1.

Ensure that the gas cylinders are empty by activating the SLS System and pressing down on
the demand valve diaphragm with the demand valve activating tool (Divex Part No. M2922)
from the Tool and Test Kit.

2.

Disconnect the pipework from the SLS System main supply penetrator.

3.

Disconnect the supply pipework, from the gas cylinders at the regulator inlet banjo.

4.

Remove the single stage regulator and two stage regulator complete with the interconnecting
pipework and withdraw to the extent that the retaining screws for the actuating sleeve can be
reached.

5.

Remove screws from actuating sleeve block.

N

OTE

The screws securing the mounting plate to the regulator body should not be touched as they are
secured by Loctite 601.

6.

Remove the banjo mounting bolt (Fig 4.8, Item 10) from the regulator.

7.

Undo the bracket and withdraw the single stage regulator from the SLS System.

8.

Disconnect the flexible gas supply hose at the regulator inlet port.

9.

Remove the regulator from the SLS System.

10.

Unscrew the end cap (Fig 4.8, Item 2) and remove the spring adjustment plate (Fig 4.8, Item
5) the spring support plate (Fig 4.8, Item 4) and the spring (Fig 4.8, Item 14).

11.

Remove the slip ring (Fig 4.8, Item 11) the diaphragm (Fig 4.8, Item 20) and the diaphragm
support plate (Fig 4.8, Item 3).

12.

Unscrew and remove the valve seat retainer (Fig 4.8, Item 6) and valve seat (Fig 4.8, Item 7).

13.

Lift out the valve pin (Fig 4.8, Item 8).

14.

Remove the spring (Fig 4.8, Item 15).

15.

Check the valve seat (Fig 4.8, Item 7) for wear and replace as necessary.

33

Grub Screw

FB079

34

Gasket

VM052

35

Relief Valve

PO20640

36

Ball Bearing

RK231

37

Mounting Plate

D29010

38

Spring

RK223

39

Spring

RK235

40

Mesh

D32870

Item

Description

Part No

«
...
82
83
84
85
86
...
»

Содержание B44771









































































































































Отзывы:

Нет отзывов

Похожие инструкции для B44771

Бренд: Icare Страницы: 3

Бренд: Lake Shore Cryotronics Страницы: 97

Monitoring System 500 II DC

Бренд: Didactum Страницы: 2

Бренд: Magene Страницы: 80

SoundTrack LxT N/Forcer

Бренд: Larson Davis Страницы: 12

Бренд: Mark-10 Страницы: 26

ACCURE 2350-GAS

Бренд: ROOTECH Страницы: 26

Бренд: THORLABS Страницы: 49

Бренд: GTR Страницы: 8

LaserRange-Master T4 Pro

Бренд: LaserLiner Страницы: 68

Бренд: Oakton Страницы: 26

Бренд: RADWAG Страницы: 12

Бренд: J-TECH Страницы: 3

Бренд: SV Страницы: 88

WaveRunner 8000-R

Бренд: Teledyne Lecroy Страницы: 20

Бренд: PASCO Страницы: 2

Бренд: Topcon Страницы: 80

Бренд: Hanna Instruments Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды