JFD B44771 Скачать руководство пользователя

Страница: 67 / 136

OM131

P1939-OM-131 R11

Chapter 4

4.2.4

Annual maintenance schedule

Visual inspection and testing of gas cylinders and HP pipework (See Section 4.3.4.1 for
details).

Strip down and service of two stage regulator (See Section 4.3.4.2 for details).

Strip down and service of single stage regulator (See Section 4.3.4.3 for details).

Strip down and service of demand regulator (See Section 4.3.4.4 for details).

Perform six monthly maintenance (see above).

4.3 P

REVENTATIVE

MAINTENANCE

PROCEDURES

Non-conformance with any of the following procedures should be fully investigated (See Section 4.4
of this Manual for guidance on fault finding).

4.3.1

Weekly maintenance procedures

4.3.1.1 Cleaning

Wash the actuation cable assembly, counterlung enclosures and cable sleeves with fresh
water to remove any build up of grit or silt etc.

Immerse the overpressure indicator in a cup of warm freshwater for a time to dissolve any
build up of salt crystals.

4.3.1.2 Visual

inspection

Inspect the main housing, which is shown in Fig 4.1, for damage or wear. Replace any
damaged or worn components as necessary.

Inspect the hoses for damage or wear, and replace any damaged or worn components as
necessary.

Inspect the harness and counterlungs, shown in Fig 4.2, for damage or wear. Replace any
damaged or worn components as necessary.

Содержание B44771









































































































































Результаты поиска

Содержание B44771

Отзывы:

Похожие инструкции для B44771

Бренды по названию

Популярные бренды

JFD B44771, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание B44771

Отзывы:

Похожие инструкции для B44771

Бренды по названию

Популярные бренды