Jet JTS-254, Инструкция по эксплуатации

Страница: 37 / 42

2
accessories.
changing accessories such as blades, bits, cutters,
etc.
improper accessories may cause hazards.
ition before plugging in power cord.
NEVER STAND ON TOOL. Serious injury could occur
if the tool is tipped or if the cutting tool is accidentally
contacted.
CHECK DAMAGED PARTS. Before further use of the
tool, a guard or other part that is damaged should be
carefully checked to ensure that it will operate
properly and perform its intended function check
for alignment of moving parts, binding of moving
parts, breakage of parts, mounting, and any other
part that is damaged should be properly repaired or
replaced.
DIRECTION OF FEED. Feed work into a blade or
cutter against the direction of rotation of the blade or
cutter only.
NEVER LEAVE TOOL RUNNING UNATTENDED.
TURN POWER OFF.
DRUGS, ALCOHOL, MEDICATION. Do not operate
tool while under the influence of drug, alcohol or any
medication.
MAKE SURE TOOL IS DISCONNECTED FROM
POWER SUPPLY
while motor is being mounted, connected or
reconnected.
WARNING: The dust generated by certain
woods and wood products can be injurious to
your health. Always run machine in well
ventilated areas and provide for proper dust
removal.
Use dust collection systems when sawing.
WARNING: The table saw must be placed to a
firm supporting, waist high surface such as a
workbench or leg stand. Many illustrations in
this manual are shown with the saw unplaced
for clarity.
WARNING! When using electric tools basic
safety precautions should always be followed
to reduce the risk of fire, electrical shock and
personal injury: read all these instructions
before attempting to operate this product and
save these instructions.
ALWAYS use guard, splitter and anti-kickback fingers
- -sawing
operations are those when the blade cuts completely
through the work piece as in ripping or cross-cutting.
ALWAYS hold the work firmly against the miter gauge
of fence.
ALWAYS use a push stick for ripping narrow stock.
Refer to ripping applications in instruction manual
where Push stick is covered in detail. See push stick
pattern Included in this instruction manual.
NEVER -
means using your hand to support or guide the
workpiece. Always use either the fence or the miter
gauge to position and guide the work.
with the path of the saw blade. KEEP your hands out
of the line of the saw blade.
either hand for any reason.
cross-cutting.
-off gauge when
cross-cutting.
cutter against the direction or rotation of the blade or
cutter only.
ree a stalled saw blade without
first turning the saw OFF. Turn off switch
immediately to prevent motor damage.
saw table for wide or long work pieces.
by:
(1) Keeping blade sharp.
(2) Keeping rip fence parallel to the saw blade.
(3) Keeping splitter and guard in place and operating.
(4) Not releasing the work before it is pushed all the
way past the saw blade.
(5) Not ripping work that is twisted or warped or does
not have a straight edge to guide along the fence.
a sudden slip could cause your hand to move into
the cutting tool.
could possibly dissolve or otherwise damage the
material. Only a soft damp cloth should be used to
clean plastic parts.
before performing any cutting operations.
hazardous dust.
dust frequently. Clean out sawdust from the interior
of the saw to prevent a potential fire hazard.
deformed.
Replace table insert when worn;
Use only saw blades recommended by the
manufacturer, which conform to EN 847-1. When
changing the saw blade beware that the width of the
groove cut of the saw blades shall not be less than and
35
LÉGER & PORTATIF
E Operation: To move the machine (B)
e. Pull the handle to positive position and you may
move the machine by pulling and wheeling
D Bedienung: Transport des Geräts (B)
e. Ziehen Sie an dem Griff, bis er einrastet. Sie
können das Gerät dann ziehend auf Rädern bewegen.
F Fonctionnement : Déplacement de la machine
(B)
e. Tirez la poignée vers le haut ; déplacez en tirant et
en faisant rouler la machine
E Clamp
D Feststellen
F Verrouillage