Jenn-Air JES8750BA Series Скачать руководство пользователя

Страница: 22 / 67

Testing Procedures

WARNING

To avoid risk of electrical shock, personal injury or death; disconnect power to range before servicing, unless
testing requires power.

22 16026926

Feature

Access Procedure

Modification Procedure

Timers Tones

Determines the number and
duration of timer reminder
chimes.

Press the

Setup

pad, then press the right

ATM

pad until TONES displays. Press the left

ATM

pad. Press the right

ATM

pad to scroll to TIMERS

TONES. Press the left

ATM

pad to select

TIMERS TONES settings.

Press the left

ATM

pad to select 2 – 30, or 2

chimes every 30 seconds for up to 5 minutes
(after the initial chime), or press the right

ATM

pad to scroll to 2 – 60, or 2 chimes every 60
seconds for up to 30 minutes (after the initial
chime), or 1 BEEP (no additional chimes after the
initial chime). Press the left

ATM

pad to select

the desired setting. Press

Setup

to exit.

Volume

Determines volumes of cook
and timer tones.

Press the

Setup

pad, then press the right

ATM

pad until TONES displays. Press the left

ATM

pad

to select VOLUME settings.

Press the right

ATM

pad until VOLUME displays.

Press the left

ATM

pad. Press the left

ATM

pad

to select HIGH, or the right

ATM

pad to scroll to

MEDIUM or LOW. Press the left

ATM

pad to

select desired setting. Press

Setup

to exit.

Energy Saver Mode

Enables a 1 watt standby
feature. If no pad is pressed
within 5 minutes, the control
enters into a sleep mode.

Press the

Setup

pad, then press the right

ATM

pad until ENERGY SAVER displays. Press the
left

ATM

pad to select ENERGY SAVER mode

settings.

Press the left

ATM

pad to enter the energy saver

mode or the right

ATM

pad to exit the energy

saver mode. Press

Setup

to exit.

Demo Mode

Enables a 1 watt standby
feature. If no pad is pressed
within 5 minutes, the control
enters into a sleep mode.

Press the

Setup

pad, then press the right

ATM

pad until DEMO displays. Press the left

ATM

pad

to select DEMO mode settings.

Press the left

ATM

pad to enable the DEMO

mode or the right

ATM

pad to exit the DEMO

mode. Once the DEMO mode begins, press any
key to exit. Press

Setup

to exit, also.

Service Mode

Enables access to service
menus.

Press the

Setup

pad, then press the right

ATM

pad until SERVICE displays. Press the left

ATM

pad to select SERVICE menu options.

Press and hold the

Back

and

Enter

pads for 5

seconds to enter SERVICE menu options. Press

Setup

to exit.

Test Access

Enables access to service
menus.

Press the

Setup

pad, then press the right

ATM

pad until SERVICE displays. Press the left

ATM

pad to select SERVICE menu options.

Press and hold the

Back

and

Enter

pads for 5

seconds to enter SERVICE menu options. Press
the right

ATM

pad to scroll to TEST menu. Press

the left

ATM

pad to select TEST options. Press

Setup

to exit.

Faults Access

Displays the 10 most recent
faults produced by the
controller.

Press the

Setup

pad, then press the right

ATM

pad until SERVICE displays. Press the left

ATM

pad to select SERVICE menu options.

Press and hold the

Back

and

Enter

pads for 5

seconds to enter SERVICE menu options. Press
the right

ATM

pad to scroll to the FAULTS menu.

Press the left

ATM

pad to select FAULTS

options. Press

Setup

to exit.

Software Versions Access

Displays the software and
EEPROM revision levels.

Press the

Setup

pad, then press the right

ATM

pad until SERVICE displays. Press the left

ATM

pad to select SERVICE menu options.

Press and hold the

Back

and

Enter

pads for 5

seconds to enter SERVICE menu options. Press
the right

ATM

pad to scroll to the VERSIONS

menu. Press the left

ATM

pad to view. Press

Setup

to exit.

Display Test

Illuminates all lamps on the
control.

Press the

Setup

pad, then press the right

ATM

pad until SERVICE displays. Press the left

ATM

pad to select SERVICE menu options.

Press and hold the

Back

and

Enter

pads for 5

seconds to enter SERVICE menu options. Press
the right

ATM

pad to scroll to DISPLAY TEST.

Press the left

ATM

pad. Press

Setup

to exit.

Control Lockout

Disables the touch keypad
control and locks the oven
cavity door.

Press the

Back

and

Setup

pads simultaneously

for 5 seconds to lock.

Press the

Back

and

Setup

pads simultaneously

for 5 seconds to unlock.

Содержание JES8750BA Series




































































Результаты поиска

Содержание JES8750BA Series

Отзывы:

Похожие инструкции для JES8750BA Series

Бренды по названию

Популярные бренды

Jenn-Air JES8750BA Series, Руководство по обслуживанию

Результаты поиска

Содержание JES8750BA Series

Отзывы:

Похожие инструкции для JES8750BA Series

Бренды по названию

Популярные бренды