background image

2

16026926

© 2006 Maytag Services

Maytag will not be responsible for personal injury or property damage from improper service procedures. Pride and

workmanship go into every product to provide our customers with quality products.  It is possible, however, that

during its lifetime a product may require service.  Products should be serviced only by a qualified service technician

who is familiar with the safety procedures required in the repair and who is equipped with the proper tools, parts,

testing instruments and the appropriate service information.  

IT IS THE TECHNICIANS RESPONSIBLITY TO

REVIEW ALL APPROPRIATE SERVICE INFORMATION BEFORE BEGINNING REPAIRS.

Important Notices for Servicers and Consumers

!

WARNING

To avoid risk of severe personal injury or death, disconnect power before working/servicing on appliance to avoid

electrical shock.

To locate an authorized servicer, please consult your telephone book or the dealer from whom you purchased this

product.  For further assistance, please contact:

Customer Service Support Center

CAIR Center

Web Site

Telephone Number

WWW.JENNAIR.COM ............................................. 1-800-536-6247

WWW.MAYTAG.COM ............................................. 1-800-688-9900

WWW.AMANA.COM................................................ 1-800-843-0304

CAIR Center  in Canada ................................................ 1-800-688-2002

Recognize Safety Symbols, Words, and Labels

DANGER

!

DANGER—

Immediate hazards which 

WILL

 result in severe personal injury or death.

WARNING

!

WARNING—

Hazards or unsafe practices which 

COULD

 result in severe personal injury or death.

CAUTION

!

CAUTION—

Hazards or unsafe practices which 

COULD

 result in minor personal injury, product or property

damage.

Important Information

Содержание JES8750BA Series




































































Отзывы: