Jenn-Air JES8750BA Series Скачать руководство пользователя

Страница: 6 / 67

16026926

Important Safety Information

Product Safety Devices

Safety devices and features have been engineered into

the product to protect consumer and servicer. Safety

devices must never be removed, bypassed, or altered in

such a manner as to defeat the purpose for which they

were intended.

Grounded Oven Frame

Ground prong on power

cord is connected to the

frame, usually a green

lead fastened by a

screw. Any part or

component capable of

conducting an electric

current is grounded by

its mounting.

If any ground wire,

screw, strap, nut, etc. is

removed for service, it

must be reconnected to

its original position with

original fastener before

the range is put into

operation. Failure to do

so can create a possible

shock hazard.

Содержание JES8750BA Series




































































Результаты поиска

Содержание JES8750BA Series

Отзывы:

Похожие инструкции для JES8750BA Series

Бренды по названию

Популярные бренды

Jenn-Air JES8750BA Series, Руководство по обслуживанию

Результаты поиска

Содержание JES8750BA Series

Отзывы:

Похожие инструкции для JES8750BA Series

Бренды по названию

Популярные бренды