background image

Page 9

Section 3.  Power Center 

Connection  

(Low Voltage)

3.1  Connecting Power and Mounting 

Bezel

WARNING

Risk of Electric Shock which can result In Serious 

Injury or Death. 

Before attempting installation or 

service, ensure that all power to the circuit supplying 

power to the system is disconnected or turned off at 

the circuit breaker. 
All wiring must be done in accordance with the 

National Electrical Code (NEC), NFPA-70. In Canada, 

the Canadian Electrical Code (CEC), CSA C22.1, 

must be followed. All applicable local installation 

codes and regulations must be followed.

1.  Plug the orange 24 VAC power plug from 

the transformer into its 3-pin terminal on 

the back of the Low Voltage Bezel. Mount 

the Bezel to the Power Center with the 

screws provided (see Figure 3).

2. 

(Shared Heater Setup only) 

Mount JVAs & run wires to Power Center. 

NOTE

  Refer to the JVA manual to install JVAs.  Run 

JVA wires back to the low voltage compartment 

of the Power Center, through low voltage 

raceway, and plug the JVAs into their sockets. 

See Figure 2 for JVA placement.  

 

Do not coil JVA cable inside Power Center. To 

shorten cable, remove JVA lid and disconnect 

the cable. Shorten, strip, and reconnect.

3.2  Connecting Control Panel Cable to 

PCB

1.  Make provisions for Jandy Control Panel 

Cable to be run between the Control Panel 

and the Power Center.

NOTE

  When cable will be run underground or in 

concrete, it must be run in conduit. Never run 

high voltage and low voltage cables in the same 

conduit.

2.  Pull the Control Panel Cable into the low 

voltage compartment. 

3.  Strip back cable jacket 6". Strip each wire 

¼". 

4.  Wire according to the Power Center PCB 

wiring diagram (see Section 5, Figure 5).

3.3  Connecting Sensors to Terminals
3.3.1  Water Temperature Sensor

1.  Drill 3/8" hole in pipe between filter pump 

and filter. Insert the sensor and use the 

clamp provided to hold the sensor in place. 

Make sure the O-ring is in place.

2.  Connect the sensor wires to the 10 pin 

terminal bar as shown in dual equipment 

wiring diagram (see Section 5, Figure 5).

3.3.2  Freeze/Air Temperature Sensor 

(Required)

Install the Freeze/Air Temperature Sensor outdoors 

where it will be subjected to outdoor temperatures, 

but not in direct sun. Connect the sensor wires to 

the 10 pin terminal bar as shown on the Power 

Center wiring diagram. Connect the other sensors 

to the 10 pin terminal bar as shown in the wiring 

diagram (see Figure 5).

3.3.3  Solar Temperature Sensor (Optional)

Install the sensor adjacent to the solar panels. 

Connect the sensor wires to the 10 pin terminal 

bar (pins 7 & 8) as shown in the wiring diagram. 

Connect the other sensors to the 10 pin terminal bar 

as shown in the wiring diagram (See Figure 5).

NOTE 

If a solar system is installed, the Freeze/Air 

Sensor will become the Solar Sensor.  A special 

Freeze Sensor Kit (Part #6996) is needed. 

Follow instructions included with the Kit.

Figure 3.  Power Center PCB (back view)

24 VAC Power Plug 

Connection

Содержание AquaLink RS6

















Отзывы: