background image

Page 10

3.4  Connecting heater to Low Voltage 

Terminal

NOTE

  Millivolt, electronic ignition, or heat pump with 

thermostatic circuitry of 24 VAC or less.

1.   If you are connecting a Low Voltage pool 

heater (for example, a Jandy Brand heater), 

connect two 14 gauge wires, designed 

for use in hot environments, to the proper 

terminals on the 10 pin terminal bar (see 

Figure 4). If you are connecting a High 

Voltage pool heater, contact Jandy for 

instructions.

Figure 4.  Jandy heater Connection

2.  Bring the 2 heater wires from the PCB over 

to the heater and wire nut in series with 

heater circuitry as if you were wiring a 

fireman's switch or a heater delay. 

3.  Turn the heater thermostat to the Spa 

position and maximum setting.

4.  Turn heater toggle switch on.
5.  Do not disconnect high limit or pressure 

switches.  

NOTE

  For Spa Heater, make connection to the Spa 

heater Interface Board and plug it into the Spa 

Heater socket.

3.5  Connecting Equipment to PCB

Connect the high voltage relay plugs into their 

appropriate sockets according to the wiring 

diagram located on the inside of the Power Center 

door (see Section 5, Figure 5).

NOTE

  Pool filter pump socket is on the far left of the 

PCB and the spa filter pump relay socket is on 

the right after aux 6 socket.

3.6  Setting DIP Switches

See the wiring diagram in Figure 5 to set all DIP 

Switches for optional operation features.

3.7  Installing Power Center Faceplate

Use the screws provided to install and secure the 

Power Center Faceplate onto the Power Center. 

Connect the Power Center can to the main circuit 

breaker and restore power to the unit and check it 

for proper operation.

Heater Toggle

Switch to ON

#14 Gauge Wire

Green 10-pin Terminal Bar

Power Center PCB/Bezel

Heater Thermostat

to Max.

Heating

Wiring

Factory Installed

Wire Loop

Jandy Heater Fireman’s

Switch Connection

Terminal 1

Terminal 2

S1

S2

6 5 4 3 2 1 10 9 8 7 6 5 4 3 2 1

4 3 2 1 4 3 2 1

RESET

SERVICE

TIME OUT

FIL

TER PU

MP

AU

X 1

AU

X 2

AU

X 3

AU

X 4

AU

X 5

AU

X 6

SPA PUMP

AUTO

POOL HEATER SPA HEATER

SOLAR

Содержание AquaLink RS6

















Отзывы: