background image

Page 4

Section 1.  Important Safety Instructions

READ AND FOLLOW ALL INSTRUCTIONS

Lire la notice technique.

All electrical work must be performed by a licensed electrician and conform to all national, state, and 

local codes. 

When installing and using this electrical equipment, basic safety precautions should always be 

followed, including the following:

  WARNING

Prolonged immersion in hot water may induce hyperthermia. Hyperthermia occurs when the internal temperature 

of the body reaches a level several degrees above the normal body  temperature of 98.6° F. The symptoms of 

hyperthermia include dizziness, fainting, drowsiness, lethargy, and an increase in the internal temperature of the 

body. The effects of hyperthermia include: 1) unawareness of impending danger; 2) failure to perceive heat; 3) 

failure to recognize the need to exit spa; 4) physical inability to exit spa; 5) fetal damage in pregnant women; 6) 

unconsciousness resulting in a danger of drowning.

 

  DANGER

To reduce the risk of injury, do not remove the suction fittings of your spa or hot tub. Never operate a spa or hot 

tub if the suction fittings are broken or missing. Never replace a suction fitting with one rated less than the flow rate 

marked on the equipment assembly

  WARNING

To Reduce the Risk of Injury -

a

The water in a spa should never exceed 104°F (40°C). Water temperatures between 100°F (38°C) and 

104°F (40°C) are considered safe for a healthy adult. Lower water temperatures are recommended for young 

children and when spa use exceeds 10 minutes.

b)  Since excessive water temperatures have a high potential for causing fetal damage during the early months of 

pregnancy, pregnant or possibly pregnant women should limit spa water temperatures to 100°F (38°C).

c)  Before entering a spa or hot tub, the user should measure the water temperature with an accurate 

thermometer since the tolerance of water temperature-regulating devices varies.

d)  The use of alcohol, drugs, or medication before or during spa or hot tub use may lead to unconsciousness with 

the possibility of drowning.

e)  Obese persons and persons with a history of heart disease, low or high blood pressure, circulatory system 

problems, or diabetes should consult a physician before using a spa.

f)  Persons using medication should consult a physician before using a spa or hot tub since some medication 

may induce drowsines while other medication may affect heart rate, blood pressure, and circulation.

  WARNING

Risk of electric shock - 

install the power center at least five (5) feet (152.4cm) from the inside wall of the pool 

and/or hot tub using non-metallic plumbing. Canadian installations must be at least three (3) meters from the 

water. 
Children should not use spas or hot tubs without adult supervision.
Do not use spas or hot tubs unless all suction guards are installed to prevent body and hair entrapment.
People using medications and/or having an adverse medical history should consult a physician before using a spa 

or hot tub.

  

AVERTISSEMENT

Danger d'electrocution - 

Les installations canadiennes doivent se trouver à au moins trois (3) mètres de l’eau.

Ne pas laisser les enfants utiliser une cuve de relaxation sans surveillance.
Pour éviter que les cheveux ou une partie du corps puissent être aspirés, ne pas utiliser une cuve de relaxation si 

les grilles de prise d'aspiration ne sont pas toutes en place.
Les personnes qui prennent des médicaments ou ont des problèmes de santé devraient consulter un médecin 

avant d’utiliser une cuve de relaxation.

Содержание AquaLink RS6

















Отзывы: