Jain Technology Xonic 100 Series, Инструкция по эксплуатации

Страница: 32 / 47

Xonic
®
100 Series
Jain Technology
www.jain.co.kr Tel. 82-2-856-4114 Fax. 82-2-856-9503
32
Input/output
–
Analog Out [1]&[2]
7. In/Output -
The flowmeter is available for 4-20m ADC output with two configurations. User can
assign each data with Analog Out [1] and [2] individually.
7.1 In/Output –
Analog Out [1]
The flowmeter has two analog output for 4-20m ADC. Both Analog Out [1] and
Analog Out [2] has exactly same functions to output data.
7.1.1 In/Output –
Analog Out [1] –
Output Data
User can assign Flow or Velocity to Analog Out.
7.1.2 In/Output –
Analog Out [1] –
Output Mode
In the case of Open Channel, User shall use the default setting, by application.
7.1.3 In/Output –
Analog Out [1] –
Calibration_Min
Caution) Do NOT use this function without manufacture’s technical instructions.
7.1.4 In/Output –
Analog Out [1] –
Calibration_Max
Caution) Do NOT use this function without manufacture’s technical instructions.
7.1.5 In/Output –
Analog Out [1] –
Span Min
User can use this menu to set the Span Minimum for the flow.
MAIN MENU
1 .
GENERAL
2 . PATH SELECT
3 . CH SETUP
4 . INSTALL
5 . OPERATE
6 . FLOW
7 . IN/OUTPUT
8 . DATALOG
9 . DIAG
IN/OUTPUT
1 . ANALOG OUT [1]
2 . ANALOG OUT [2]
3 . RELAY OUT [1]
4 . RELAY OUT [2]
5 . ANALOG IN [1]
6 . ANALOG IN [2]
ANALOG OUT [1]
1 . OUTPUT DATA
2 . OUTPUT MODE
3 . CALIBRATION_MIN
4 . CALIBRATION_MAX
5 . SPAN MIN
6 . SPAN MAX
7 . 2mA SET OUTPUT DATA
1 . NONE
2 . FLOW
3 . VELOCITY
4 . ANALOG IN 1
5 . ANALOG IN 2
1 . OUTPUT DATA
2 . OUTPUT MODE
3 . CALIBRATION_MIN
4 . CALIBRATION_MAX
5 . SPAN MIN
6 . SPAN MAX
7 . 2mA SET
ANALOG OUT [1]
1 . BY APPLICATION
2 . [CH 1] ONLY
3 . [CH 2] ONLY
OUTPUT MODE
1 . OUTPUT DATA
2 . OUTPUT MODE
3 . CALIBRATION_MIN
4 . CALIBRATION_MAX
5 . SPAN MIN
6 . SPAN MAX
7 . 2mA SET
ANALOG OUT [1] SPAN MIN
m³/h
0
Press [ MENU ] – 7. IN/OUTPUT
▪
Analog Output [1]&[2]
▪
Relay Out [1]&[2]
▪
Analog In [1]&[2]
Press [ MENU ] – 7. IN/OUTPUT – 1. ANALOG OUT
[1]
– 1. OUTPUT DATA
▪
None – Disable Output Function
▪
Output the Flow Data
▪
Output the Velocity Data
▪
Re-transmit the Data from Analog Input [1]
▪
Re-transmit the Data from Analog Input [2]
▪
Press [ MENU ] – 7. IN/OUTPUT – 1. ANALOG OUT
[1] – 2. OUTPUT MODE
▪
By Application – Set Up by the program.
▪
[CH 1] only – Not available for Open Channel
▪
[CH 2] only – Not available for Open Channel
Press [ MENU ] – 7. IN/OUTPUT – 1. ANALOG OUT [1] – 3. CALIBRATION_MIN
Press [ MENU ] – 7. IN/OUTPUT–1. ANALOG OUT [1] – 4. CALIBRATION_MAX
Press [ MENU ] – 7. IN/OUTPUT – 1. ANALOG OUT [1] –
5. SPAN MIN
➢
The value should be same with the minimum flow
user set in the menu, 5.2 Lower Flow Limit.