Jacobsen AR3 Скачать руководство пользователя страница 279

Страница: 279 / 342

8-14

4181384 First Edition

CUTTING UNITS

Mechanical Troubleshooting—TR-3

Condition

Probable Cause

Remedy

Reel drive motors do not reach full speed.

Engine speed is insufficient, not set to
specification.

Check/adjust engine speed. (Refer to

“Safety, Operation, and Maintenance
Manual.”)

Reel drive motor(s) and/or hydraulic
system performance is reduced.

Check hydraulic system performance

(pump output, motor operation, valve
operation, relief valve settings, etc.).
(See “Tests and Adjustments” on page
6-26.)

Reel drive motors do not engage.

Mow switch is not engaged.

Engage mow switch. (Refer to Safety,

Operation, and Maintenance Manual.)

Mow switch is faulty.

Test mow switch. (See “Rocker Switches”

on page 4-80.)

Mow solenoid is faulty.

Test mow solenoid. (See “Solenoid Test”

on page 4-68.) (See “Mow Circuit” on
page 4-56.)

Cutting unit(s) do not lower completely to
ground.

Cutting unit(s) movement is restricted.

Check/remove cutting unit restriction.

Lift/lower circuit is faulty.

Test lift/lower circuit. (See “Symptom:

Lower solenoid does not energize.” on
page 4-55.)

Cutting unit(s) do not rise off ground.

Faulty lift cylinder.

Test lift system. (See “Lift/Steer Pump

Test” on page 6-41.) (See “Cutting
Unit/Charge Pump Test” on page 6-31.)

Cutting units have too much weight on
them.

Adjust weight transfer as necessary. Use

weight transfer switch to transfer weight
off of the cutting units. (Refer to “Safety,
Operation, and Maintenance Manual.”)

Hydraulic system performance is reduced.

Check hydraulic system performance

(pump output, motor operation, valve
operation, relief valve settings, etc.)
(See “Instrument Test Procedures” on
page 6-29.)

Cutting unit roller does not rotate.

Roller is out of round and restricted by
scraper and/or scraper is bent.

Replace roller or scraper. (See “Front

Roller” on page 8-42 or “Rear Roller”
on page 8-44.)

Roller bearing is faulty.

Replace roller bearing. (See “Front Roller”

on page 8-42 or “Rear Roller” on
page 8-44.)

Содержание AR3























































































































































































































































































































































Результаты поиска

Содержание AR3

Отзывы:

Похожие инструкции для AR3

Бренды по названию

Популярные бренды

Jacobsen AR3, Техническое руководство по ремонту

Результаты поиска

Содержание AR3

Отзывы:

Похожие инструкции для AR3

Бренды по названию

Популярные бренды