Jacobsen AR3 Скачать руководство пользователя страница 260

Страница: 260 / 342

STEERING

4181384 First Edition

7-11

Figure 7-12

NOTE

Record the location of the fittings before removal to
ensure correct installation.

Remove fittings (23 and 24) from the steering
cylinder (15).

10. Inspect O-rings on fittings (23 and 24). Replace as

needed.

11. Remove the rod end (21) and jam nut (20) from the

steering cylinder (15).

12. Bend the tab washers (19) away from the screws (18)

and remove the screws.

13. Remove the journal (22) from the steering cylinder

(15).

14. Inspect bushings (16 and 17). Replace as needed.

Installation Notes

• Install the steering cylinder by reversing the order of

removal.

Figure 7-13

• Install (tighten) screw (25) fully into the rear wheel

support (28) before installing the nut (27).

• Tighten nut (27) to 103 lb-ft (140 N·m).

• Apply grease to lubrication fitting (26). (Refer to

“Safety, Operation, and Maintenance Manual” for
grease specifications.)

• Check hydraulic oil level. Add oil as needed. (Refer to

“Safety, Operation, and Maintenance Manual” for
hydraulic oil specifications.)

Disassembly and Assembly

See Figures 7-14 through 7-19.

Figure 7-14

Remove (unscrew) the end cap (1) from the cylinder
body (2).

TN1218

TN1216

TN1251

Содержание AR3























































































































































































































































































































































Результаты поиска

Содержание AR3

Отзывы:

Похожие инструкции для AR3

Бренды по названию

Популярные бренды

Jacobsen AR3, Техническое руководство по ремонту

Результаты поиска

Содержание AR3

Отзывы:

Похожие инструкции для AR3

Бренды по названию

Популярные бренды