Jacobsen AR3 Скачать руководство пользователя страница 108

Страница: 108 / 342

ELECTRICAL

4181384 First Edition

4-51

Charging Circuit

Symptom: Battery not charging.

Symptom: Alternator light stays on.

Probable Cause

Remedy

Faulty alternator output circuit.

Make sure alternator output cable and battery positive (+) cable terminals are clean and

tight.

Check continuity between starter battery terminal and battery positive (+) terminal.

Continuity must be indicated.

Faulty battery ground circuit.

Make sure battery negative (–) cable terminals are clean and tight.

Check continuity between battery negative (–) terminal and ground.

Continuity must be indicated.

Faulty battery.

Check specific gravity of the individual battery cells.

Probable Cause

Remedy

Open fuse 7.5A fuse F7.

Test fuse. (See “Fuse Test” on page 4-61.)

Faulty control module switched power
circuit.

With the key switch in the run position, measure voltage between control module terminal

3 and ground. Measure voltage between control module terminal 8 and ground.

Voltage must be approximately 12 VDC.

Faulty alternator.

With the engine running, measure voltage between jump start connector terminals.

Voltage must be approximately 14 VDC.

If the voltage is below 12 volts, replace the alternator.

Содержание AR3























































































































































































































































































































































Результаты поиска

Содержание AR3

Отзывы:

Похожие инструкции для AR3

Бренды по названию

Популярные бренды

Jacobsen AR3, Техническое руководство по ремонту

Результаты поиска

Содержание AR3

Отзывы:

Похожие инструкции для AR3

Бренды по названию

Популярные бренды