Jacobsen AR3 Скачать руководство пользователя страница 185

Страница: 185 / 342

5-38

4181384 First Edition

HYDROSTATIC POWER TRAIN

Disassembly

Figure 5-68

Scribe or mark a line (1) along the side of hydraulic
motor sections (2) to mark the alignment of motor
segments before disassembly.

Figure 5-69

NOTE

Use caution when removing screws as motor segments
will be free to move.

Remove four screws (3) from the valve housing (4).

Figure 5-70

NOTE

The spacer (8) may remain with the disk valve (5) when
the valve housing is removed.

Remove the valve housing assembly (7) and spacer
(8) from the channel plate (6).

Remove the disk valve (5) from the valve drive (9)
and channel plate (6).

Figure 5-71

NOTE

Do not remove the alignment pin (11) unless replacement
is required.

Remove the balance plate (10), spacer (12), and
spring washer (13) from the valve housing (14).

Remove O-rings (15 and 16) from the balance plate
(10).

TN1290

TN1294

TN1295

TN1305

Содержание AR3























































































































































































































































































































































Результаты поиска

Содержание AR3

Отзывы:

Похожие инструкции для AR3

Бренды по названию

Популярные бренды

Jacobsen AR3, Техническое руководство по ремонту

Результаты поиска

Содержание AR3

Отзывы:

Похожие инструкции для AR3

Бренды по названию

Популярные бренды