Jacobsen AR3 Скачать руководство пользователя страница 145

Страница: 145 / 342

4-88

4181384 First Edition

ELECTRICAL

Installation Notes

• Install the engine oil pressure switch by reversing the

order of removal.

• Apply Teflon

tape to the threads of the oil pressure

switch before installing.

Engine Temperature Switch

Removal and Installation

See Figures 4-88 and 4-89.

NOTE

Naturally aspirated engine shown; turbocharged engine
is similar.

Park the mower safely. (See “Park Mower Safely” on
page 1-7.)

Disconnect the battery negative (–) cables at the
battery.

Open the engine hood.

Figure 4-88

WARNING

Rotate pressure cap (1) 1/2-turn to relieve pressure
in cooling system.

Figure 4-89

NOTE

Label all wires before disconnecting to ensure correct
installation.

Disconnect wiring connector (2) from the engine
temperature switch (4).

Remove the engine temperature switch (4) from the
thermostat housing (3).

Installation Notes

• Install the engine temperature switch by reversing the

order of removal.

• Apply Teflon

tape to the threads of the engine

temperature switch before installing.

Required Materials

Telfon

Tape

Engine coolant is hot and under pressure! Allow
the cooling system to cool completely before
performing service.

Rotate the filler cap 1/2-turn counterclockwise
and allow pressure to vent before removing filler
cap.

TN0997

Required Materials

Telfon

Tape

TN1104

Содержание AR3























































































































































































































































































































































Результаты поиска

Содержание AR3

Отзывы:

Похожие инструкции для AR3

Бренды по названию

Популярные бренды

Jacobsen AR3, Техническое руководство по ремонту

Результаты поиска

Содержание AR3

Отзывы:

Похожие инструкции для AR3

Бренды по названию

Популярные бренды