Jacobsen AR3 Скачать руководство пользователя страница 174

Страница: 174 / 342

HYDROSTATIC POWER TRAIN

4181384 First Edition

5-27

Disassembly and Inspection

Figure 5-31

Scribe a line (1) along the side of hydraulic motor
sections (2) to mark the position of motor segments
before disassembly.

Figure 5-32

NOTE

Use caution when removing screws, as motor segments
will be free to move.

Remove seven screws (3) from the end cover (4).

Figure 5-33

NOTE

The spacer (9) may remain with the disk valve (6) when
the valve housing is removed.

Remove the end cover assembly (8) and spacer (9)
from the disk valve (6) valve plate (5).

Remove the disk valve (6) from the valve drive (7)
and valve plate (5).

Figure 5-34

Remove the O-ring (10) from the valve plate (11).

NOTE

Record the orientation of the valve drive before removing
to ensure correct installation.

Remove the valve plate (11) from the gear wheel set
(12).

TN1309

TN1310

TN1311

TN1312

Содержание AR3























































































































































































































































































































































Результаты поиска

Содержание AR3

Отзывы:

Похожие инструкции для AR3

Бренды по названию

Популярные бренды

Jacobsen AR3, Техническое руководство по ремонту

Результаты поиска

Содержание AR3

Отзывы:

Похожие инструкции для AR3

Бренды по названию

Популярные бренды