J.A. Woollam M-2000 Скачать руководство пользователя страница 58 | Manualshive

Страница: 58 / 178

background image

58

©2023 J.A. Woollam Co.

M-2000® Hardware Manual

4.5

System Alignment (with
Manual Tip/Tilt)

Note:

Automated Tip/Tilt alignment is an optional accessory that may or
may not have been purchased with your system. If your purchase
included Automated Tip/Tilt, please see Section 4.6 for System
Alignment (with Automated Tip/Tilt).

System alignment is the adjustment of the source and receiver components
relative to the variable angle base of the M-2000 system. It is required when the
system is first delivered, when first mounting the system onto a base or
chamber, or whenever the integrity of the alignment is in question. Figure 4-10
shows the basic components of the M-2000 system, and this naming convention
will be followed throughout these instructions.

In the straight-through position (angle = 90°), the white light beam should be
centered on both the Receiver Unit aperture and the 4-quadrant alignment
detector that is located inside the Receiver Unit. This alignment is easily tested,
using the following instructions, which also describes correction to the
alignment. All operations will be performed from within the

Hardware

tab of

CompleteEASE.

Note:

A System Alignment should only be performed when the instrument
is first delivered, after mounting the Light Source and Receiver
components onto a base or chamber, or if the integrity of the
alignment is in question.

Note:

Alignment of the Light Source and Receiver tilt stages on the base
should only be adjusted when the base is in the straight-through
position. Any adjustment screw should never need to be turned
more than ½-1 full turn. If so, it is likely something is not
mounted/aligned properly; check previous steps to be sure they
were done correctly.

Note:

Optional focusing optics must be removed before continuing (if
attached).

«
...
56
57
58
59
60
...
»

Содержание M-2000



















































































































































































Отзывы:

Нет отзывов

Похожие инструкции для M-2000

Бренд: Oldham Страницы: 43

Бренд: Kane Страницы: 20

Бренд: Macnaught Страницы: 4

Бренд: CA.MI Страницы: 68

Бренд: Percussion Play Страницы: 3

Бренд: ELGO Electronic Страницы: 24

OPERA CONTROL CENTER SERVER - V 3.5

Бренд: OPTICOM Страницы: 21

Бренд: Aktobis Страницы: 7

IMI SENSORS 604B11

Бренд: PCB Piezotronics Страницы: 19

Бренд: GREISINGER Страницы: 20

Бренд: S+S Regeltechnik Страницы: 32

Бренд: Leica Страницы: 2

DIGIMET E30 Preset

Бренд: MATO Страницы: 20

Litemaster Pro L-478DR

Бренд: Sekonic Страницы: 16

Бренд: Velleman Страницы: 38

Бренд: Rebel Страницы: 28

Бренд: E Instruments Страницы: 2

Бренд: Hanna Instruments Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды