J.A. Woollam M-2000 Скачать руководство пользователя страница 150 | Manualshive

Страница: 150 / 178

background image

150

©2023 J.A. Woollam Co.

M-2000® Hardware Manual

Figure 10-13. Typical QTH lamp.

6.

Carefully align the two legs of the lamp into the two holes in the socket.
There is no polarity on this lamp.

7.

Gently push the bulb down into the socket until it is fully seated.

8.

Replace the cover and tighten the SHC screws to lock the cover closed.

9.

Reset the hour meter by pressing the reset button located on the front of
the M-2000 Detector and Lamp Power Supply Module.

Note:

When a new lamp is installed, it must be aligned so that the
maximum amount of light is available for sample measurement.
The optimal position should not change much from lamp to lamp,
but fine adjustment is needed to achieve best results.

Lamp Alignment

1.

Turn on the lamp power supply. Allow the lamp to warm up for at least
20 minutes.

2.

Ensure the Base is in the 90° (straight-through) position and the Z-
position is raised such that the sample stage will not block the beam from
hitting the receiver unit’s aperture.

3.

Select

Hardware

>

Controls

>

General

> ‘Align Sample’. Choose No when

prompted for the full system alignment.

4.

Locate the Average Signal reading (bottom of the alignment screen) and
make a mental note of the signal value.

5.

There is a small adjustment screw located on the bottom of the lamp
housing. This screw controls the vertical position of the lamp inside the
lamp housing. Using the 1/16” Allen wrench, adjust the screw until the
signal reading is maximized.

«
...
148
149
150
151
152
...
»

Содержание M-2000



















































































































































































Отзывы:

Нет отзывов

Похожие инструкции для M-2000

Бренд: Hammond Страницы: 130

Бренд: E Instruments Страницы: 144

Бренд: Keithley Страницы: 31

Бренд: Keithley Страницы: 63

Бренд: Keithley Страницы: 18

Бренд: Keithley Страницы: 73

Бренд: Armstrong Monitoring Corporation Страницы: 12

Бренд: Veeco Страницы: 349

Бренд: GrainPro Страницы: 7

Бренд: Caen Страницы: 50

Бренд: EPE Conseil Страницы: 3

Бренд: Primes Страницы: 48

Бренд: Omicron Страницы: 76

Бренд: Galileo Страницы: 30

Бренд: Alpes Lasers Страницы: 41

Бренд: Thermo Scientific Страницы: 56

Бренд: Velleman Страницы: 15

Бренд: Ratek Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды