iWave iW-RainboW-G21D Скачать руководство пользователя страница 52

Страница: 52 / 106

REL1.0

Page 52 of 106

RZ/G1H Qseven Development Platform Hardware User Guide

iWave Systems Technologies Pvt. Ltd.

2.7.4

SDIO Port

The RZ/G1H Qseven Carrier Board supports SDIO interface through RZ/G1H

CPU’s

SDHI2 interface. This SDHI2 signals

from Qseven MXM connector is connected to SD/MMC connector (J30) to support Standard SD interface. This

connector supports up to 4-bit data transfer with card detect and write protect. Also it supports SDIO activity Green

LED (D8) on board for SDIO bus transfer indication.

The main power to SD/MMC connector is 3.3V and it is connected through power switch to support power

enable/disable feature. This power enable/disable is controlled from the SDIO_PWR# pin of Qseven MXM connector.

This SD/MMC connector (J30) is physically located at the bottom of the board as shown below.

Figure 16: SD/MMC Connector

Содержание iW-RainboW-G21D











































































































Результаты поиска

Содержание iW-RainboW-G21D

Отзывы:

Похожие инструкции для iW-RainboW-G21D

Бренды по названию

Популярные бренды

iWave iW-RainboW-G21D, Руководство пользователя по оборудованию

Результаты поиска

Содержание iW-RainboW-G21D

Отзывы:

Похожие инструкции для iW-RainboW-G21D

Бренды по названию

Популярные бренды