IVT JST-12L, Инструкция по эксплуатации

Страница: 9 / 108

9
Manual instruction
EN
Safety regulation for the use
General safety rules
This model of Jump Starter (JST-12L) is designed
to give a safe and dependable service if operated
in accordance with the following instructions. This
device is intended to be used as a power supply, for
example to start a car with a discharged battery, and
to supply compressed air.
The following listed safety instructions should serve
you for the right use and for the protection of your
own safety. Therefore please read this very carefully.
When passing this tool to a third person, these
instructions must be handed too.
Retain this user manual and all other literature
supplied with your tool for any future reference.
Comply with the safety information and the
warnings on the tool.
Be familiar with the controls and the proper use of
the tool before attempting to use it and above all,
make sure you know how to stop to use it in case
of emergency.
Following these simple instructions will also
maintain your tool in good working order.
• The tool must be assembled correctly before use.
• Only use the tool for its designed purposes.
• In addition to the design of the tool there may
be safety decals that must be considered and
indications about the safety equipment to use.
The prevention of accidents is dependent upon
the awareness, common sense and proper training
of everyone involved in the operation, transport,
maintenance and storage of the tool.
• Never leave the tool unattended.
• Never allow children to use the tool. Children
should be supervised to ensure that they do not
play with the tool.
• Keep children and pets away. All onlookers
should be kept at a safe distance away from the tool
when it is in use.
• The user is responsible for third parties while
working with the tool.
• People who aren’t acquainted with the
operating instructions, children, juveniles who have
not yet reached the minimum age for using this tool
and people under the influence of alcohol, drugs or
medication are not allowed to use the tool . Local
regulations may restrict the age of the operator.
WARNING: The consumption of alcohol,
medication and drugs, plus states of
illness, fever and fatigue will affect your ability to
react. Do not use this tool in any of these situations.
• Make sure that all the protective devices (if
present) are fitted and are in good condition.
• Never operate the tool with defective safety
devices or guards (if present), or without safety
devices in place .
• Inspect the entire tool to look for loose parts
(e.g. nuts, bolts, screws, etc.) and for any damage.
Check at frequent intervals if screws and bolts
are properly tight to be sure the equipment is in
safe working condition. Repair or replace them, if
necessary, before using the tool. Serious injury to
the operator and to the bystanders could result if
there’s a damage to the tool .
• While using the tool, dress properly. Do not
wear loose clothing or jewelry that could become
caught by the tool. Wear suitable working clothes.
It is recommended that legs and feet are covered, to
protect from flying debris. Long air should be tided
back.
• Keep handles and grips dry, clean and free from
oil and grease.
• Use a proper protective equipment. Use safety
glasses and safety gloves. Also use a dust mask
during pulverulent operations or if exaust gases
are present. When necessary, use also non-slipping
boots or shoes, hardhat and earplugs. If the noise
level exceeds 85 dB(A), ear protection is obligatory.
WARNING! Use personal protective
equipment! Safety devices and the
personal protective equipment protect
your own health and the health of others and
ensure a trouble-free operation of the tool .
• Do not start to use the tool if it is in an inverted
position or it is not in the right working order.
• Ensure that you have a good stand, while you
operate with the tool. Keep proper footing and
balance at all times.
• Keep work area clean. Cluttered areas invite
injuries. Before use, all foreign bodies must be
removed from the working area, also pay attention
to foreign objects during the operation.
• Do not force the tool.
• Only work in daylight or sufficiently good
artificial light. Never operate the tool without good
visibility.
• Be careful not to drop the tool or hit it against
obstacles.
Stay alert. Watch what you are doing.
Distraction can cause you to lose