ITW Simco-Ion IQ Power Скачать руководство пользователя страница 5 | Manualshive

Страница: 5 / 36

background image

3

IQ Power™ BPS

5201197 Rev. D

Features

• Three types of IQ Power™ static neutralizing bars are available to suit the

specific application.

• Static bar disconnect plug pre-installed on static bar cable for quick and easy

installation. Plug also identifies bar type to power supply automating power

supply set-up.

•  Single momentary push-button calibration simplifies set-up.
•  Ionization emitter points current limited to enhance operator safety.
•  Ionization emitter points of special alloy to extend operating life of emitter

points.

• Continuous “T” slot at back of static bar and mounting brackets for easy and

flexible installation.

• Bar graph display on power supply indicates ionizing performance of system.
• Indicators on power supply display status of neutralizing system, power, service

required and detection of system faults.

• Relay contact output “echoes” indicators on power supply for remote sensing and

alarm.

• Optional computer interface allows for remote monitoring and logging of the

system’s performance.

• Optional web speed encoder for gathering web speed data.
• Optional control station that provides power and a communication hub for IQ

Power™ static neutralizing systems.

«
...
3
4
5
6
7
...
»

Содержание Simco-Ion IQ Power





































Отзывы:

Нет отзывов

Похожие инструкции для Simco-Ion IQ Power

Бренд: B&K Страницы: 5

Бренд: B&K Страницы: 28

Бренд: Zenbooth Страницы: 60

Бренд: AccuMed Страницы: 14

Бренд: TAS Страницы: 25

FreeStyle Comfort

Бренд: CAIRE Страницы: 33

Бренд: Ransomes Страницы: 282

Ransomes HR 6010

Бренд: Jacobsen Страницы: 10

Бренд: Radial Engineering Страницы: 16

Бренд: R&S Страницы: 61

MT765 Challenger

Бренд: Fast Страницы: 31

Бренд: Delfield Страницы: 2

Vetter QuickStrut

Бренд: Idex Страницы: 14

Бренд: Eurotops Страницы: 8

Бренд: KRATOS SAFETY Страницы: 36

Бренд: Sagitter Страницы: 12

Бренд: Invacare Страницы: 271

ADB KLEMANTIS AS 1000

Бренд: Osram Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды