ITW Simco-Ion Ion-O-Vac Скачать руководство пользователя страница 3

Страница: 3 / 36

5200860 Rev H

Ion-O-Vac

1. SAFETY WARNINGS

NOTE!

Statements identified with a NOTE indicate precautions necessary

to avoid potential equipment failure.

CAUTION!

Statements identified with a CAUTION indicate minor or

moderate injury is possible.

WARNING!

Statements identified with a WARNING indicate serious

injury is possible.

NOTE!

This equipment must be correctly installed and maintained. Adhere

to the following notes for safe installation and operation.

1. This equipment must be correctly installed and properly maintained. Adhere

to the following cautions for safe installation and operation.

2.   Read instruction manual before operating or installing device.
3.   Qualified service personnel must do installation and repairs.
4.   Ground the frame of the machine on which the power supply and neutralizing

bars are mounted.

5. Disconnect supply voltage to power supply before connecting neutralizing bar

to the high voltage terminal strip.

CAUTION! Electrical Shock Hazard

1. Do not touch bar when power supply is energized.
2. Disconnect supply voltage to power supply before connecting bar or

performing any maintenance to the system.

WARNING! Fire Hazard

Do not install or operate equipment in close proximity to any flammable solvents

or flammable materials.

This equipment must be correctly installed and properly maintained as outlined in

this manual. Adhere to the following cautions for safe installation and operation:

1. Disconnect and lockout all power before servicing this machine, unless

instructions state otherwise. Turn off web drive equipment and remove web, if

possible, before performing maintenance.

Содержание Simco-Ion Ion-O-Vac





































Результаты поиска

Содержание Simco-Ion Ion-O-Vac

Отзывы:

Похожие инструкции для Simco-Ion Ion-O-Vac

Бренды по названию

Популярные бренды

ITW Simco-Ion Ion-O-Vac, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Simco-Ion Ion-O-Vac

Отзывы:

Похожие инструкции для Simco-Ion Ion-O-Vac

Бренды по названию

Популярные бренды