background image

17

5200860 Rev H

Ion-O-Vac

CAUTION! Electrical Shock Hazard

Power supply must be turned off during disconnection and re-connection of static 

bar.

1.  Disconnect all but one static bar from the high voltage terminal.
2.  Use TensION to test several points on the bar.  If orange-red glow occurs, the 

bar is functioning properly.  Disconnect that bar and reconnect next bar.  Check 

all bars until faulty bar(s) is located by no glow.

D167RY, D267RY, F167 and F267 Power Unit Operational Test

Equipment needed:

•  Multimeter – Fluke Model 70 Series or equivalent
•  High Voltage Probe – Fluke Model 80 K or equivalent with minimum 20 

KVAC rating

CAUTION

:  High Voltage

Refer testing to qualified service personnel.  Failure to do this can affect a 

product’s operation and can result in personal injury.

1.  Verify power supply is off and static bar(s) are disconnected.
2.  Set multimeter for AC voltage so that it can read 20KVAC full scale.  Connect 

high voltage probe to multimeter and connect ground lead on high voltage 

probe to ground.

3.   Connect a short (approximately 4”) piece of stiff wire to contact on end of high 

voltage probe.

4.   Insert wire into high voltage connector making contact with screw head inside 

high voltage connector on power supply.

5.   Turn on power supply.  Operating voltage should be between 7500 VAC and 

8100 VAC.  The power supply is not functioning properly if it is not operating 

between these voltages.

NOTE

:  Input voltage to power supply must be the same as on power supply 

label.

6.  Turn off power supply.
7.  Remove high voltage probe from connector in power supply.

Содержание Simco-Ion Ion-O-Vac





































Отзывы: