Isokern Magnum 28 Скачать руководство пользователя страница 32

Страница: 32 / 72

Combustible sheathing such as plywood and particle board may be used to cover the front face of the MAGNUM

smoke dome and be in direct contact with it. If sheathing protrudes in front of the firebox, application of such combustible

sheathing must assure that the sheathing is held a minimum of eight inches (8”) away from each side of the MAGNUM opening

and a minimum of eight inches (8”) above the top of the MAGNUM opening. (Figure 70 & 71) (9” for models 60 & 72)

Do not build a combustible framed wall out in front of the MAGNUM firebox.

If sheathing and framing are to be installed across the front face of the MAGNUM smoke dome, then the framing and sheathing

must be held a minimum of eight inches (8”) above the top of the MAGNUM firebox opening. This means that framing and

sheathing across the smoke dome front must be kept at or above the MAGNUM damper beam.

FIGURE 71

FIGURE 70

Required Clearances (when sheathing protrudes beyond front of firebox)

FINISHED OPENING

MIN. DIM'N.

MIN.

WOOD (FLAMMABLE)
SHEATHING

MIN.

Содержание Magnum 28









































































Результаты поиска

Содержание Magnum 28

Отзывы:

Бренды по названию

Популярные бренды

Isokern Magnum 28, Инструкция по установке, эксплуатации, обслуживанию и руководство владельца

Результаты поиска

Содержание Magnum 28

Отзывы:

Бренды по названию

Популярные бренды