Isokern Magnum 28 Скачать руководство пользователя страница 20

Страница: 20 / 72

Flush Wall Finish Detail

MAGNUM fireplaces are designed to be installed so that the rough front face of the firebox and damper beam project into the room

approximately one-half inch (1/2”) beyond the face of the rough framing members that create the room’s wall surface.

The MAGNUM smoke dome front sits two and three-fourths inches (2-3/4”) back from the rough face of the firebox and damper

beam. This set back dimension allows for one and one-half inch (1-1/2”) framing plus one-half inch (1/2”) thick wall board to pass

in front of the smoke dome and at the same time align flush with the room face of the MAGNUM damper beam. Set in this position,

framing and wall board are kept to the required eight inches (8”) above the firebox opening top (Figure 25).

Important: Do not build a frame wall in front of the MAGNUM firebox and damper beam. (Figure 26)

FIGURE 25

FIGURE 26

FRAMING PROTRUDES

PAST FIREBOX FRONT

DRYWALL FLUSH

WITH FIREBOX

FRONT

Содержание Magnum 28









































































Результаты поиска

Содержание Magnum 28

Отзывы:

Бренды по названию

Популярные бренды

Isokern Magnum 28, Инструкция по установке, эксплуатации, обслуживанию и руководство владельца

Результаты поиска

Содержание Magnum 28

Отзывы:

Бренды по названию

Популярные бренды