manualshive.com logo in svg
  • Главная
  • /
  • Isokern
  • /
  • Magnum 28
  • /
  • Инструкция по установке, эксплуатации, обслуживанию и руководство владельца

Isokern Magnum 28, Инструкция по установке, эксплуатации, обслуживанию и руководство владельца

Поделиться
Скачать
Isokern Magnum 28 Скачать руководство пользователя страница 2

TABLE OF CONTENTS

General Information      .......................................................................................................................................

Intended Use Statement  ......................................................................................................................................

Safety Instructions  ..............................................................................................................................................

Warnock-Hersey Listing Label  ...........................................................................................................................   

Assembled Firebox & Smoke Dome Dimensions  ..............................................................................................         

Component List & Dimensions  ..........................................................................................................................         

Assembled Firebox Dimensions 60 & 72.............................................................................................................         

Component List & Dimensions 60 & 72..............................................................................................................         

Required Clearance to Combustibles  .................................................................................................................         

Rough Framing Dimensions & Corner Location Layout  ...................................................................................    

Assembly Instructions         .................................................................................................................................           

Access Modification  ...........................................................................................................................................

Firebrick Installation  ..........................................................................................................................................

Flush Wall Finish Detail  ..................................................................................................................................... 

Assembly Instructions - 60  .................................................................................................................................

Assembly Instructions - 72  ................................................................................................................................. 

DM 54 Chimney System - 60 & 72  ....................................................................................................................     

Required Clearances (When sheathing protrudes beyond front of firebox)  .......................................................       

Required Clearance to Combustible Framing  ....................................................................................................        

Required Clearances to Insulation and Vapor Barriers  ......................................................................................      

Flush Wall Fire Brick Finish Detail  ...................................................................................................................      

Flush Wall Brick Finish Detail ............................................................................................................................      

 

Interior Masonry Veneer Fireplace Finishes & Clearances...................................................................        

 

Masonry Veneer Construction Details ..................................................................................................        

Non Combustible Finished Facing Requirements & Clearance to Combustible Trim .......................................         

Concrete Support  ...............................................................................................................................................            

DM Chimney System  ........................................................................................................................................           

 

General Information  ............................................................................................................................        

 

Component List & Dimensions.............................................................................................................          

Component Weights ............................................................................................................................................ 

        

Installation  ...........................................................................................................................................     

 

Lateral Support  ....................................................................................................................................      

 

Offset Block  .........................................................................................................................................      

 

Brick Ledge Installation  .......................................................................................................................

              Brick Ledge Load Capacity  ..................................................................................................................

  

Crown Caps  .......................................................................................................................................... 

Height Requirements  ..........................................................................................................................................        

 

Structural Information  ..........................................................................................................................    

 

Common Chimney Terminations  .........................................................................................................     

Class “A” Metal Flue  .........................................................................................................................................      

Specialty Applications  .......................................................................................................................................      

 

Two Story Stacked Installations  ..........................................................................................................    

Fire-Lite Application General Information......................................................................................................... .

Fire-Lite Safety Instructions (See page 6)  

 

Fire-Lite Application - Required Clearance to Combustibles ...............................................................   

 

Fire-Lite Application - Combustible Floor System ............................................................................... 

 

Fire-Lite Application - Raised Metal Platform ..................................................................................... 

Fire-Lite Application - Flush Wall Finish Detail .................................................................................................

FTF-13 or Equivalent Chimney System ..............................................................................................................

FTF-13 or Equivalent Installation Components...................................................................................................

Summary .............................................................................................................................................................. 
Notes ....................................................................................................................................................................

3

4

5-6

7

8

9 

10

11

12

13

14-17

18

19

20

21-25

26-30

31

32

33

34

35

36

37

38

39

40

41-50

41

42

43

44

45-46

47-50

51

52

53

54

55

56

57

58-67

58-59

60

61

62

63-64

65

66-67

68

69-70

71

2

Содержание Magnum 28









































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды