Iseki SF310 Скачать руководство пользователя страница 38

36

SF310,370

For example, when moving uphill if the front wheels slip, 
the mechanism stays in 4WD. But moving downhill hill if 
the front wheels slip and lose grip, and begin to slip down 
the slope, it shifts to 2WD, that is, braking effect of the 
HST unit is lost, which means loss of front mower control.
From another point of view, when you try to turn the front 
mower on a slope, rear wheel driving power is lost and the 
front mower may slip down the slope, which is also very 
dangerous.

2.3. TILT LOCK LEVER

The steering wheel column is tiltable to gain the optimum 
wheel angles. To adjust the angles, pull up the tilt lock 
lever while holding the steering wheel with the other hand, 
and the lock is released. Select the most adequate angle 
within the four setting position. Then push down the lever 
securely to lock the steering wheel column. 

CAUTION: Only adjust steering tilt when the 
machine is parked.

3. FLOOR PEDALS AND LEVERS

(1) Master brake pedal
(2) HST forward travel pedal
(3) HST reverse travel pedal
(4) Independent brake pedal (RH) (E6 type)
(5) Independent brake pedal (LH) (E6 type)
(6) Dif-lock pedal
(7) Parking brake lever (Except G type)

 

(3) Tilt lock lever 

5

6

4

7

1

2

3

FIG. 38

3

FIG. 37

Содержание SF310





























































































Отзывы: