Iseki SF310 Скачать руководство пользователя страница 28

Страница: 28 / 92

SF310,370

(6) Fan warning label
(Code No. 1705-902-006-0)

WARNING: RISK OF ENTANGLEMENT
Stay clear of the fun while it is turning.

(7) Belt warning label
(Code No. 1674-904-008-0)

WARNING: RISK OF ENTANGLEMENT
Stay clear of the belt while it is running.

(8) Starter warning label
(Code No. 1705-902-007-0)

DANGER: RISK OF ELECTRIC SHOCK
Start the engine only from the seat using the key.

(9) Radiator warning label
(Code No. 1705-902-008-0)

WARNING: HIGH PRESSURE STEAM AND HOT WATER
Never remove the radiator cap during or just after opera-
tion. The water in the radiator is very hot and highly pres-
surized, which could cause burns.

(10) Lift lock label
(Code No. 1720-906-001-0)

WARNING: When raising up the mower deck for service,
apply the lift lock of hydraulic cylinder.

(11) PTO label
(Code No. 8654-901-002-0)

WARNING: Stay clear of the PTO shaft while the engine
is running.

Содержание SF310





























































































Результаты поиска

Содержание SF310

Отзывы:

Iseki SF310, Руководство оператора, Страница: 28 / 92

Результаты поиска

Содержание SF310

Отзывы: