manualshive.com logo in svg

Interlogix CDX-135Z, Руководство по установке

Поделиться
Скачать
Interlogix CDX-135Z Скачать руководство пользователя страница 5

 
 

5   P/N 466-5307 

• REV A • ISS 15MAR17                                              ©2017 United Technologies Corporation   

 

2.  Power on all detectors by attaching the detectors onto the mounting bracket (trim 

plate)  to  activate  the  battery,  or  by  carefully  turning  the  activation  wheel  with  a 
screwdriver.  See Figure 3. 

 

 

 

 

 

 

 

 

 

Figure 3 

•   The  GREEN  LED  will  fade  on  and  off  once,  then  the  RED  LED  will  begin 

fading on/off every 3 seconds. 

NOTE:

  If  no  further  steps  are  taken  within  15  minutes  of  initial  power  up,  the 

wireless function will turn off. The unit will then perform as a standard single station 
detector.   

NOTE: 

At  any  time  during  wireless  setup,  if  you  have  a  problem,  reset  the  unit's 

wireless settings as described in section 

“Resetting a Detector’s Wireless Settings” 

3.  Push and hold the Test/Hush button on any one detector until two beeps are heard 

(approximately  4  seconds)  and  then  release  the  button.  This  detector  will 
automatically create a new wireless network. 
•   A brief series of quick GREEN LED blinks will occur and then the GREEN LED 

will fade on/off every second on the button-pushed detector (network creator). 

4.  Wait for the other wireless detectors to join the wireless network. 

•   A brief series of quick GREEN LED blinks will occur and then the GREEN LED 

will fade on/off approximately every 3 seconds. 

NOTE:

  At  this  point,  you  can  push/release  the  test  button  once  on  any  detector, 

and the RED LED will flash the number of enrolled detectors.  

5.  Wait  for  the  network  setup  to  timeout  (approximately  15  minutes),  OR  to 

immediately  close  the  network,  push  the  Test/Hush  button  until  two  beeps  are 
heard (approximately 4 seconds) and then release the button. 
•   Network  closed  sound  on  each  detector  confirms  network  has  been  closed.  

GREEN LED flashes once every 60 seconds to indicate normal operation. 

6.  After selecting the proper location for your detector, attach the mounting bracket to 

the wall or ceiling. To ensure aesthetic alignment of the detector with the hallway, 

Содержание CDX-135Z



























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды