manualshive.com logo in svg

Interlogix CDX-135Z, Руководство по установке

Поделиться
Скачать
Interlogix CDX-135Z Скачать руководство пользователя страница 24

 
 

24   P/N 466-5307 

• REV A • ISS 15MAR17                                              ©2017 United Technologies 

Corporation   

 

Product Ordering 

Model 

Description 

CDX-135Z 

Wireless Interconnected Combination Smoke and Carbon 
Monoxide Detector with Heat and Freeze Sensor, Sounder, UL 
217, UL 268, UL 2034, UL 2075, ULC S531 

Accessories 

 

SM-200 

Smoke! In A Can (canned smoke) for functional testing of smoke 
detectors 

SM-EXT1 

Extension tube for Smoke! In A Can 

Regulatory Information 

This device complies with FCC Part 15 and Industry Canada license exempt RSS 
standard(s). Operation is subject to the following two conditions: (1) this device may not 
cause interference, and (2) this device must accept any interference, including 
interference that may cause undesired operation of the device. 

Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux 
appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions 
suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de 
l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est 
susceptible d'en compromettre le fonctionnement. 

 

RF EXPOSURE 

All transmitters regulated by IC must comply with RF exposure requirements listed in 
RSS-102 - Radio Frequency (RF) Exposure Compliance of Radiocommunication 
Apparatus (All Frequency Bands). Currently this device is approved for use for when 20 
cm can be maintained between the antenna and users.  Specific Absorption Rate 
(SAR) evaluation is required if the separation distance between the user and/or 
bystander and the antenna and/or radiating element of the device is less than or equal 
to 20 cm. Exceptions are listed in RSS-102. Note that integration < 20 cm will require 
further certification with IC such as a Multiple listing and Class IV Permissive Change 
application. 

Tous les émetteurs régulés par Industrie Canada doivent ętre conformes à la notice 
RSS-102 d'Industrie Canada concernant la Conformité des appareils de 
radiocommunication aux limites d'exposition humaine aux radiofréquences (toutes 
bandes de fréquences).  Ce produit est ainsi approuvé pour une utilisation d'au moins 
20 cm entre l'antenne et toute personne à proximité.  Une évaluation du Débit 
d'Absorption Spécifique (DAS) est requise si cette distance de séparation est inférieure 
ou égale à 20 cm. Des exceptions sont toutefois répertoriés dans la notice RSS-102. 
Mais il est souligné que l'utilisation d'un dispositif à moins de 20 cm nécessite une 

Содержание CDX-135Z



























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды