manualshive.com logo in svg

Interlogix CDX-135Z, Руководство по установке

Поделиться
Скачать
Interlogix CDX-135Z Скачать руководство пользователя страница 10

 
 

10   P/N 466-5307 

• REV A • ISS 15MAR17                                              ©2017 United Technologies 

Corporation   

 

returned  for  service.    See  Permanently  Disable  Detector/Discharge  Battery  section  to 
determine how to prepare the unit for shipment or disposal. 

 

        WARNING:    DO  NOT  USE  AN  OPEN  FLAME  TO  TEST  YOUR  DETECTOR.  
YOU  COULD  DAMAGE  THE  DETECTOR  OR  IGNITE  COMBUSTIBLE  MATERIALS 
AND START A STRUCTURE FIRE. 
 

FUNCTIONAL SMOKE TEST 

The smoke test verifies that the unit activates when detecting smoke, that the 
transmitted signal is received by the receiver/panel, and that the panel reports the 
alarm to the central monitoring station. The smoke test should be performed annually. 
A canned smoke testing agent must be used for the functional smoke test 

NOTE:

  Use Interlogix brand of Smoke! In A Can part number SM-200. 

1.  Wait at least 90 seconds after installation to test the smoke detector. 

2.  Make sure the GREEN LED is flashing for normal operation (one GREEN LED 

blink every 60 seconds). 

3.  From a distance of 2 - 4 feet (0.6 

– 1.2m), aim spray for 1 – 2 seconds at the vents 

or side of the detector. 

4.  The alarm will sound within 1 

– 10 seconds if the detector functions properly. 

5.  Press the Test/Hush button to quiet the sounder. 

6.  Contact the central monitoring station to verify they received the alarm report. 

7.  Alert the central monitoring station when you are finished testing. 

NOTE:

  An alternative method for performing a functional smoke test in the field is to 

hold a smoldering punk or cotton wick close to the detector and direct the smoke into 
the vent openings until an alarm is indicated. 

 

CO INSPECTION AND FUNCTIONAL GAS TEST  

A canned CO testing agent must be used for the CO functional gas test. Contact a local 
supplier for canned CO gas 

– Solo C6

TM 

CO Detector Tester. 

NOTE:

  Cans of Solo C6

TM

 CO Detector Tester can be sourced from the manufacturer 

per the following contact information: 

 
Product Code:  Solo C6-024 
SDi, 1345 Campus Parkway, Suite A18, Wall Township, NJ  07753  USA 
Tel: (732) 751-9266, Fax: (732) 751-9241 
Email:  [email protected], Web:  www.sdifire.com 
 

1.  Wait at least 20 minutes after installation to test the CO detector. 

Содержание CDX-135Z



























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды