IntelliQuilter HQ-AVANTE 03.25.16 Скачать руководство пользователя | Manualshive

Страница: 16 / 22

background image

16

Remove the protective cover from the power supply connector.

Connect the power cable to the power supply: BLACK wire to the negative terminal,
the wire with the in-line diode to the positive terminal.

Fig. 16

Put back the protective cover.

For strain relief, tie the cable to the hole on the side of the power supply with wire
tie. Plug in the AC adapter jack.

«
...
14
15
16
17
18
...
»

Содержание HQ-AVANTE 03.25.16























Отзывы:

Нет отзывов

Похожие инструкции для HQ-AVANTE 03.25.16

Бренд: Janome Страницы: 48

AUTOSTROKE AST-200-V2

Бренд: StoneAge Страницы: 28

MMAC-Plus 9F116-01

Бренд: Cabletron Systems Страницы: 4

Бренд: Caberg Страницы: 16

Бренд: Dacor Страницы: 4

Бренд: Hahnel Страницы: 176

Бренд: Jabra Страницы: 2

Бренд: Jabra Страницы: 38

Бренд: Velleman Страницы: 2

Бренд: Velleman Страницы: 9

Бренд: X10 Страницы: 1

Бренд: Yakima Страницы: 7

Бренд: Yakima Страницы: 6

Бренд: Yakima Страницы: 10

Бренд: Yakima Страницы: 12

Бренд: M2M Страницы: 20

Zeus F745-VTX STACK

Бренд: HGLRC Страницы: 19

Бренд: Blue Ox Страницы: 7

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды