Inova TableBed Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 55

Inova TableBed Скачать руководство пользователя страница 6

Tech support is readily available if needed

Email:

[email protected]

Phone:

866.528.2804

TableBed

| ASSEMBLY MANUAL

PLEASE NOTE:

Your Bed may look different

than what is shown in the pictures and

videos throughout this manual

QUICK START GUIDE

(CONT.)

TOOLS NEEDED:

Electric Power Drill
#2 Phillips Bit
#3 Phillips Bit (provided)
#2 Square Bit (provided)
4mm Allen Wrench (provided)
4mm Allen Bit (provided)
9/16” Wrench
#2 Phillips Screwdriver
Hammer
Pliers
Utility Knife
Vise Grips
Flashlight
QR Code Scanner App
(To view videos)

HARDWARE LIST:

Bolts:

H-020 Panel Bolts, 25 mm
H-021 Panel Bolts, 40 mm
H-060 Pan Head Machine Bolts

Screws:

H-014s Euro Screws
H-019 Machine Screws
H-039 Wood Screws
H-065 Panel Screws
H-107s Flat Head Euro Screws
H-425 Machine Screws

Other:

H-003 Wood Dowels
H-008 Leveler Feet
H-011 Minifix Pins
H-035 Clevis Pin
H-077 Wide Angle Brackets
H-928 Cotter Pin
M-36 Cam Roller

«
...
4
5
6
7
8
...
»

Содержание TableBed
























































Отзывы:

Нет отзывов