manualshive.com logo in svg

Inova TableBed, Инструкция по сборке, Страница: 10 / 55

Поделиться
Скачать
Inova TableBed Скачать руководство пользователя страница 10

Tech support is readily available if needed 

Email: [email protected]

Phone: 866.528.2804

A. 

Lay the Cabinet Front on the floor and screw 

the H-011 Minifix Pins into the small holes 

of the Cabinet Front. Tap the H-003 Wood 

Dowels into the larger holes of the Cabinet 

Front.

B. 

Prepare to attach Cabinet Bottom to Cabinet 

Front.

C. 

Make sure all the Minifix Cams in the Cabinet 

Bottom have their arrows pointing towards 

the outside edge of the panel to allow the 

pins to slide into the Cams, as shown.

D. 

Slide the Cabinet Bottom onto the Minifix 

Pins and Wood Dowels in the Cabinet Front, 

then tighten the Minifix Cams in the Cabinet 

Bottom.

Use this version of Step 2 if your TableBed is an Open Back Model

STEP 2:

  Attach Cabinet Front to Cabinet Bottom

A

H-003

H-011

Cabinet Front

B

Cabinet Bottom

Cabinet Front

Cabinet Bottom

Minifix Cam Arrow

C

Cabinet Front

Minifix Cam Arrow

D

Содержание TableBed
























































Отзывы:

Нет отзывов