Inova Solutions ontime Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 46

Inova Solutions ontime Скачать руководство пользователя страница 14

OnTime Clock

Installation and User Guide

Firmware Version 2

All claims based on information publicly available at time of printing. All other product or service names mentioned

in this document may be trademarks of the companies with which they are associated.

© 2017 Inova Solutions | All rights reserved | page 9

4.6. Surface Mounting the Digital Clock

The following is a recommended procedure for surface mounting the digital clock. No
mounting kit is required.

1.

Determine the clock mounting location.

2.

Mark two points 10” (25.4 cm) apart which are level and centered on the data

cable outlet.

Note that both models are mounted with a ten inch distance between screw hole centers;
however, the best location for the wall jack varies.

Refer to the templates in Figure 4

and Figure 5 to ensure that you line the wall jack up with the recess in the back of
the unit.

Figure 4: Mounting Template for 4-Digit Clocks

«
...
12
13
14
15
16
...
»

Содержание ontime















































Отзывы:

Нет отзывов