Innova Innova Filomuro Incasso SLWI Скачать руководство пользователя страница 28

28

 INSTALLATION

•  in heating function decreases by 1 °C after one hour and 

by another degree after 2 hours 

•  in cooling function decreases by 1 °C after one hour and 

by another degree after 2 hours

 Maximum ventilation speed

To select the operation at the maximum ventilation speed

– 

press the 

 key for about 2 seconds

The symbol 

 on indicates the maximum speed function enable

Maximum power output is immediately obtained both in 
heating and cooling.

After reaching the desired room temperature, select a dif-
ferent function to increase the thermal and acoustic com-
fort.

 Set the key lock

To set-up the key locking

– 

press both 

 

 keys for 2 seconds

The text 

 appearing on the display

All settings are inhibited by the user.

Repeat the sequence to unlock the control.

 Brightness  reduction

To reduce the display brightness 

– 

press the 

 key for 5 seconds

The text 

 appearing on the display

– 

press the 

 key to decrease the value, wait 20 seconds

After 20 seconds from the last action the panel brightness 
will be reduced to increase the comfort during night use. 
On the display will appear only the room temperature.

 Deactivation

To deactivate the display

– 

press the key 

 for about 2 seconds

All the light signals go off

In stand-by mode the control ensure an antifreeze safety.

 Room temperature probe offset adjustment

To adjust the room temperature probe offset

– 

from display off, hold the key  

 for about 5 seconds

Access to the variation menu of the AIR probe offset displayed on the display

Use this adjustment carefully.

This adjustment must be carried out only after having 

found actual deviations from the room temperature using 
a reliable tool.

Adjust the measured value within a range of +/- 10 °C in 
steps of 0,1 °C.

After 20 seconds from the last action the control goes out 
and the settings is memorized.

 Settings menu EDA/EDB649 - EWG/EWW649

Through the  control it is possible to access the settings 
menu.

The settings menu parameters can only be changed by 

qualified personnel.

Содержание Innova Filomuro Incasso SLWI





































Отзывы: