background image

This equipment has been tested and found to comply with the limits for a Class B digital 
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable 
protection against harmful interference when the equipment is operated in a commercial 
environment. This equipment generates, uses, and can radiate radio frequency energy, and, 
if not installed and used in accordance with the Installation Manual, may cause harmful 
interference to radio communications. Operation of this equipment in a residential area is likely 
to cause harmful interference, in which case the user will be required to correct the interference 
at the user’s own expense.

This Class A digital apparatus meets all requirements of the Canadian Interference-Causing 
Equipment Regulations.

Cet appareil numerique de la classe A respecte toutes les exigences du Reglemente sure le 
materiel brouilleur du Canada.

© 1998 through 2009 Schlage Biometrics, Inc. – ALL RIGHTS RESERVED
Document Part Number: 70100-6003 – Revision 3.1 – June, 2009

HandPunch is a trademark of Schlage Biometrics, Inc.

The trademarks used in this Manual are the property of the trademark holders. The use of 
these trademarks in this Manual should not be regarded as infringing upon or affecting the 
validity of any of these trademarks.

Schlage Biometrics, Inc. reserves the right to change, without notice, product offerings or 
specifications.

No part of this publication may be reproduced in any form without the express written 
permission from Schlage Biometrics, Inc.

Содержание SCHLAGE HP-3000






































































































Отзывы: