manualshive.com logo in svg

Ingersoll-Rand SCHLAGE HP-3000, Руководство пользователя

Поделиться
Скачать
Ingersoll-Rand SCHLAGE HP-3000 Скачать руководство пользователя страница 45

HandPunch 3000/4000 Manual

43

Erasing the Memory

There are two options when erasing the memory of the HandReader:

1. 

Setup

2. 

All

The erasing of the setup will set the HandReader’s address, passwords, etc., 
back to factory defaults.

Choosing the All option will take the HandReader’s setup back to factory 
defaults plus erase all user databases and datalogs. This action cannot be 
undone. If there is a software that is managing the system then the users can 
be downloaded back to the HandReader if needed.

The erase memory function allows a HandReader’s setup and/or user 
database to be erased.
Perform the following steps to erase the setup programs but retain the user 
database.

1. 

With system power OFF, depress reset switch.

2. 

Turn system power ON and wait 5 seconds.

3. 

LCD screen will display.

Erasing 
HandReader 
Memory

ERASE

:1 SETUP

:9 ALL!!!

Содержание SCHLAGE HP-3000






































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды