Ingersoll-Rand SCHLAGE HP-3000 Скачать руководство пользователя страница 49

Страница: 49 / 101

HandPunch 3000/4000 Manual

The display appears as follows.

ENTER ID
*:

Enter your ID number on the keypad and place your hand on the platen for
verification.

If verification is successful, the display appears as follows.

Enter Command Menu

Press the

CLEAR

and

ENTER

keys simultaneously to enter a

command menu.

The display appears as follows:

ENTER PASSWORD

Press the default password for the menu you wish to enter.

Press 1 for the Service Menu.
Press 2 for the Setup Menu.
Press 3 for the Management Menu.
Press 4 for the Enrollment Menu.
Press 5 for the Security Menu.

Press

ENTER

and the first command option in the selected menu

appears.

If No One
is Enrolled
in the
HandPunch

If Users are
Enrolled
in the
HandPunch

Содержание SCHLAGE HP-3000






































































































Результаты поиска

Содержание SCHLAGE HP-3000

Отзывы:

Бренды по названию

Популярные бренды

Ingersoll-Rand SCHLAGE HP-3000, Руководство пользователя

Результаты поиска

Содержание SCHLAGE HP-3000

Отзывы:

Бренды по названию

Популярные бренды