Immergas VICTRIX MAIOR 35 X TT 1 ERP Скачать руководство пользователя страница 23

23

INS

TALLER

US

ER

MAINTEN

AN

CE TECHNI

CI

AN

Error 

Code

Anomaly signalled

Cause

Boiler status / Solution

10

Insufficient system 

pressure

Water pressure inside the central heating circuit that is sufficient to 

guarantee the correct operation of the boiler is not detected.

Check on the boiler pressure gauge (1) that 

the system pressure is between 1÷1.2 bar 

and restore the correct pressure if necessary.

12

Storage tank probe 

anomaly

(optional)

If the P.C.B. detects a fault in the boiler probe 

(when the boiler is 

connected to an external storage tank unit) 

, the boiler cannot pro-

duce DHW and signals a fault.

The boiler does not satisfy the DHW pro-

duction requests (1).

15

Configuration error

If the board detects an anomaly or incongruity on the electric wiring, 

the boiler will not start.

If normal conditions are restored the boiler 

restarts without having to be reset. Check 

that the boiler is configured correctly (1)

16

Fan anomaly

This occurs if the fan has a mechanical or electrical fault.

Press the Reset button (1)

20

Parasite flame block

This occurs in the event of a leak on the detection circuit or anomaly 

in the flame control unit.

Press the Reset button (1)

23

Return probe anomaly

The board detects an anomaly on the return NTC probe.

The boiler does not start (1)

24

Push button control 

panel anomaly

The board detects an anomaly on the pushbutton panel.

If normal conditions are restored the 

boiler restarts without having to be reset 

(1).

29

Flue probe anomaly

The board detects an anomaly on the flue gas probe

The boiler does not start (1)

31

Loss of remote control 

communication

This occurs if an incompatible remote control is connected, or if 

communication between the boiler and the remote control is lost.

Power cycle the boiler. If the Remote Con-

trol is still not detected on re-starting the 

boiler will switch to local operating mode, 

i.e. using the controls on the control panel. 

In this case the “Central Heating” (1) mode 

cannot be activated.

36

IMG Bus communica-

tion loss

Communication between the various components is interrupted due 

to an anomaly on the boiler control unit, on the zone control unit or 

on the IMG Bus.

The boiler does not satisfy the room heating 

requests (1).

37

Low power supply 

voltage

This occurs when the power supply voltage is lower than the allowed 

limits for the correct boiler operation. 

If normal conditions are restored the boiler 

restarts without having to be reset (1)

38

Loss of flame signal

This occurs when the boiler is ignited correctly and the burner flame 

switches off unexpectedly; a new attempt at ignition is performed and 

if normal conditions are restored, the boiler does not have to be reset.

If normal conditions are restored the boiler 

restarts without having to be reset (1) (2)

43

Block due to loss of 

flame signal

This occurs if the ''Flame signal loss'' error occurs many times in a 

row within a preset period (38).

Press the Reset button, before restart-

ing, the boiler will run a post-ventilation 

cycle. (1)

44

Block for exceeding the 

maximum accumulat-

ed time, close gas valve 

opening

This occurs if the gas valve remains open for longer than required 

for normal operation, without the boiler switching on. 

Press the Reset button (1)

45

ΔT high

The boiler detects a sudden, unexpected increase in the ΔT between 

the flow probe and the system return probe.

The power of the burner is limited to pre-

vent damage to the condensation module 

and once the right ΔT is restored, the boiler 

resumes regular operation. Make sure there 

is water circulating in the boiler, that the 

pump is configured according to system 

requirements and that the return probe 

works properly. (1) (2)

46

Low temperature safety 

thermostat (optional)

During normal operation, if an anomaly causes excessive overheat-

ing of the flow temperature in low temperature conditions, the boiler 

blocks.

In this case, after suitable cooling, it is pos-

sible to reset the thermostat (see relative 

instructions sheet). (1).

47

Burner power limita-

tion

Should flue high temperature be detected, the boiler reduces power 

supplied so as not to damage it.

(1)

51

CAR Wireless com-

munication failure

If there is no communication between the boiler and Wireless version 

CAR, an anomaly is signalled. From this moment, it is only possible 

to control the system by means of the control panel of the boiler itself.

Check operation of the Wireless CAR, 

check the battery charge (refer to the relative 

instructions booklet).

59

Main supply voltage 

frequency block

The board detects a main supply voltage frequency anomaly.

The boiler does not start (1)

60

Anomaly pump 

blocked

The pump is stopped due to one of the following causes:
Impeller blocked, electrical fault.

Try to unblock the pump as described in 

the relative section. If normal conditions are 

restored the boiler restarts without having 

to be reset (1)

61

Air in circulator pump

Air is detected inside the pump; the pump cannot work.

Vent the pump and the central heating cir-

cuit. If normal conditions are restored the 

boiler restarts without having to be reset (1)

(1) If the shutdown or fault persists, contact an authorised company (e.g. Authorised Technical After-Sales Service).

(2) The anomaly can only be verified in the list of errors in the “Information” menu

STD.002549/004

Содержание VICTRIX MAIOR 35 X TT 1 ERP

















































Отзывы: